Sony VGP-PRUX1 - Manual (Page 2)

Specifications
Connectors Port replicator connector: Custom connector (1)
USB: Type-A connector (3)*
i.LINK (IEEE 1394): S400 4-pin (1)
External display output:
MONITOR (a): Analog RGB, VGA, D-sub 15-pin (1)
AV OUT (T): compatible with NTSC/PAL,
stereo mini jack (1)
LAN connector: LAN (100BASE-TX/10BASE-T) (1)*
* The specifications are the same as those of the personal
computer you are using. For details, refer to the manuals
provided with your personal computer.
Power requirements
AC adapter**
** Use the unit with an AC adapter (VGP-AC16V7) that is
compatible with your personal computer.
Operating temperature
41°F to 95°F (5°C to 35°C)
(temperature gradient less than 18°F (10°C)/hour)
Operating humidity
20% to 80% (not condensed), provided that humidity is
less than 65% at 95°F (35°C)
(hygrometer reading of less than 84°F (29°C))
Storage temperature
–4°F to 140°F (–20°C to 60°C)
(temperature gradient less than 18°F (10°C)/hour)
Storage humidity
10% to 90% (not condensed), provided that humidity is
less than 20% at 140°F (60°C)
(hygrometer reading of less than 95°F (35°C))
Dimensions Approx. 6.0 (w) × 2.9 (h) × 4.6 (d) inches
(Approx. 150.2 Ч 71.9 Ч 114.7 mm)
Mass Approx. 8.8 oz. (249 g)
Supplied accessories
Operating instructions (1)
Holder (1)***
***When using the unit, attach the holder. For details on how to
attach it, refer to the manuals provided with your personal
computer.
Design and specifications are subject to change without notice.
Notes on use
• Use the unit with an AC adapter that is compatible with your personal
computer. See also the manuals provided with your Sony personal
computer for more information.
• To disconnect the unit completely from the main voltage, unplug the AC
adapter.
• Make sure that the socket outlet is easily accessible.
• Do not place the unit in locations that are:
– Extremely hot or cold
– Dusty or dirty
– Very humid
– Vibrating
– Subject to strong magnetic fields
– Sandy
– Subject to direct sunlight
• Do not apply mechanical shock or drop the unit.
• Make sure that nothing metallic comes into contact with the metal parts
of the unit. If this happens, a short-circuit may occur and the unit may be
damaged.
• Do not operate the unit with a damaged cord.
• Do not operate the unit if the unit itself has been dropped or damaged.
• Always keep the metal contacts clean.
• Do not disassemble or convert the unit.
• While in use, it is normal for the unit to get warm.
• Keep the unit away from TV or AM receivers, because it can disturb TV
or AM reception.
• i.LINK, USB, PC card slot, Printer, DVI-D and MONITOR connectors are
not supplied with Limited Power Sources if those connectors are
provided.
• When connecting or disconnecting the unit, handle it carefully.
• When transporting the unit, prevent foreign objects from causing a
malfunction by using the battery pack, the connector covers and the
supplied slot protectors if there is any.
• When transporting your personal computer, be sure to remove the unit
first. Moving your personal computer with the unit installed could cause
the unit to fall off, resulting in personal injury, or damage to the unit or
your personal computer.
• When transporting the unit, detach the holder.
• If there are any dust or dirt particles on the port replicator connector,
your personal computer may not be able to detect the port replicator
when it is connected (even if the particles are invisible to the eye).
If the connection seems to be poor, remove the AC power adapter and
battery and wipe off the connector and the area around it on both the
personal computer and port replicator. Commercial air dusters are also
effective for blowing away residual dust and dirt.
Be careful not to damage the connectors while cleaning them.
On cleaning
Clean the unit with a soft dry cloth or a soft cloth lightly moistened with a
mild detergent solution. Do not use any type of solvent, such as alcohol or
benzine, which may damage the finish.