Allstar Products Group 9931TK - Manual

Manufacturer’s Limited Warranty
Allstar warrants its radio controls to be free from defect in material and workmanship for a period of one (1)
year from the date of purchase. To obtain service, contact your dealer.
To obtain service under this warranty the buyer must obtain authorization instructions for the return of any
goods from Allstar before returning the goods. The goods must be returned with complete identification,
with copy of proof-of-purchase, freight prepaid and in accordance with Allstar’s instructions or they will not
be accepted. In no event will Allstar be responsible for goods returned without proper authorization or
identification.
Goods returned to Allstar for warranty repair within the warranty period, which upon receipt by Allstar are
confirmed to be defective and covered by this limited warranty, will be repaired or replaced at Allstar’s sole
option, at no cost and returned pre-paid. Defective parts will be repaired or replaced with new or factory
rebuilt parts at Allstar’s sole option.
This limited warranty does not cover non-defect damage, damage caused by unreasonable use, damage
caused by improper installation or care, vandalism or lightning, fire or excessive heat, flood or other acts of
God (including, but not limited to misuse, abuse or alterations, failure to provide reasonable and necessary
maintenance), labor charges for dismantling or reinstalling a repaired or replaced unit, or replacement
batteries.
These warranties are in lieu of all other warranties, either expressed or implied. All implied warranties of
merchantability and/or fitness for a particular purpose are hereby disclaimed and excluded. Under no
circumstances shall Allstar be liable for consequential, incidental or special damages arising in connection
with the use or inability to use this product. In no event shall Allstar’s liability for breach of warranty, breach
of contract, negligence or strict liability exceed the cost of the product covered hereby. No person is
authorized to assume for Allstar any other liability in connection with the sale of this product.
This warranty gives you specific legal rights. Warranty effective after July 24, 2002.
Copyright © 2002 c.p.Allstar Corporation PART NUMBER 111243 REV F
After installing your receiver and transmitter, check the
operation of your radio controls by moving
approximately 45 feet back from the garage door, then
press the transmitter button. Operation at this distance
should be reliable. However, environmental conditions
and the location of the transmitter and receiver will
affect distance.
• If the transmitter doesn’t activate the operator check the
coding on both the transmitter and receiver. The code
setting must match exactly .
• If the distance is inadequate check the battery and
replace if necessary.
• To maximize the operating distance move the
transmitter to different locations in the car until a
satisfactory distance is achieved. Vanity mirrors on sun
visors will affect performance.
• If the receiver is in the proximity of a metal beam or
other obstruction it may be necessary to relocate the
receiver to increase the operating range.
• If multiple receivers are mounted closer than 15 feet,
blocking and interference may occur. Move the
receivers further apart.
• If system does not work at any distance, check that the
receiver terminals are connected to the proper operator
terminals.
• If the HomeLink® transmitter does not activate the
operator or distance is inadequate,verify proper
operation using the hand-held transmitter. Contact your
HomeLink® system provider for help with
configuring the HomeLink® transmitter and to resolve
distance problems when using the HomeLink® system.
Operational Check
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry
Canada. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
WARNING
Unexpected door operations can cause personal injury or property damage.
Classic Quik-Code Transmitter
Installation Instructions
Replacement for Models:
•9921T •9931T •8822T •8832T
•8833T •9921MT •9931MT •9921TK
•9931TK •8832TK •9931TK6
The Classic Quik Code Transmitter makes it
possible to operate a single or group of remotely
controlled devices such as a garage door opener,
with a single transmitter.
Programming the Classic is done by simply:
1.
Put the transmitter in program mode.
2. Select the button you wish to use.
3. Enter your 9 digit code.
Product Features
Disconnect power to operator before any installation or repair. Follow all
instructions provided by the manufacturer of your operator.
WARNING
INSTRUCTIONS FOR REPLACEMENT TRANSMITTERS
Select the block of switches below that best matches the one in the
transmitter or receiver that you are replacing.
*The grids display an EXAMPLE using the code shown on the switches to the left.
Allstar Radio Controls are compatible with HomeLink®.
Homelink® is a registered trade mark of Johnson Controls, Inc.
1 2 3 4 5 6 7 8 9
- - 0 0 + + - 0 +
1 2 3 4 5 6 7 8 9
- - + + - - + + -
1 2 3 4 5 6 7 8 9
- - + + - - + + -
OR
1 2 3 4 5 6 7 8 9
- - 0 0 + + - 0 +
turn page
Go to
Step 1a
turn page Go to Step 1...
turn page Go to Step 1...
9 switches w/ + 0 -
8 switches w/ + 0 -
9 switches w/ On & Off
Follow these simple instructions.
Please read the instructions completely before starting.
Further instructions are available at www.allstarcorp.com