Sony LF-B1 - Manual (Page 2)

STEP
2
STEP
3
Setup to Watch TV at Home
Put the Base Station into Setup Mode
(Registration Possible)
Press the SETUP MODE button on the rear panel of the base station. Keep the
button held down until the SETUP MODE LED starts blinking.
z Tip
Make all settings up to “STEP 2: Connecting Your Computer to the Base Station to Watch TV” while the
SETUP MODE LED is blinking.
The Setup Mode (registration possible) is available for 5 minutes. If the SETUP MODE LED stops
blinking, keep pressing the SETUP MODE button again until the SETUP MODE LED starts blinking.
* In the Setup Mode, the wireless LAN operates on the 2.4 GHz channel.
Connect Your Computer to the Base
Station to Watch TV
1
2
3
Double click the icon on the desktop to start LocationFree™ Player.
While the SETUP MODE LED is blinking, select a base station from the list,
choosing one with a green icon, and then click [Connect].
If the SETUP MODE LED is not blinking, press the SETUP MODE button again to
switch to Setup Mode (registration possible).
When the message “Registration completed. Select [OK] to connect to the
Base Station and start watching TV/video” appears, click [OK].
Green icon
Make TV and Video Settings with the LocationFree™ Player
■ Configure the TV channels
Click anywhere inside the window, and then click [Settings]
at the bottom right of the window. 1
2
3
1
2
3
1
2
3
z Tip
[Settings] at the bottom right of the window
appears only when you are connected to the
base station. When you are not connected,
click [Connect] at the bottom left, select the
base station you want to set up from the list
that appears, click [Properties], and then
click [Channel Settings].
[Settings]
Select [Channel Settings] below [TV/Video Settings], and then
configure all the settings.
Select [ON] or [OFF].
If you subscribe to cable
TV, select the [ON] option.
Clear the check boxes for
channels that you do not watch.
Click [OK] to close the [Settings] window.
1
2
■ Configure the TV on-screen remote
(For the set top box (STB) connection in STEP 1)
* For the TV antenna connection in STEP 1, no need to configure the TV
remote control.
Click anywhere inside the window, and then click
[Settings] at the bottom right of the window.
Select [TV/Video Settings], [Remote Settings], and then
[TV].
Select the make and type
of the connected device.
Click [OK] to close the [Settings] window.
Click anywhere inside the window, then click [TV]. Click
[Remote], then the on-screen remote control appears.
■ Configure the on-screen remote for video
(For the connection to other devices in STEP 1)
2
3
Click anywhere inside the window, and then click [Settings] at the
bottom right of the window.
Select [TV/Video Settings], [Remote Settings], and then [Video 1]
or [Video 2], then select the make and type of the connected
device.
If the configuration above is correct, each time you click [Power], your
device should turn on or off.**
** After clicking [Power], it takes five seconds or more for the device to
respond. If it does not respond, make sure that the make and type
are correct, and then try again.
Click [OK] to close the [Settings] window.
Click anywhere inside the window, then click the type of the connected
device. Click [Remote], then the on-screen remote control appears.
[Power] Select the make.
Select the type.
Make Easy Setup Settings for the Base Station with Your Computer
Setup to Watch TV On-the-Go
2
3 Click [Enter].
✱ Follow the on-screen instructions to
proceed to the NetAV check. In the
[NetAV Setup] page, read the supplied
Dynamic DNS Terms-of-Use Agreement
and then click [Agree].
Afterwards
Use the
LocationFree™
Player to watch TV
and videos.
For details on
settings and
operation of the
LocationFree™
Player, refer to the
supplied Operating
Instructions (included
on the supplied
CD-ROM).
* You can view the
Operating Instructions
from the [Start] menu
in Windows.
Connect Your Computer to the Base Station
Check the base station NETWORK LED.
Check whether the base station NETWORK LED is turned on.
When not turned on:
Make sure the router power is turned on and the LAN cable is connected correctly.
1
To
connect y
our computer to the base station with a router
Modem without router function
Modem with inter
nal router
• Connect to the router by wireless
Router
(UPnP Compatible)
Base station
DSL or cable modem
to Internet
Hub or wireless
access point (without
router function)
• Connect to the router by wireless
• Connect to the
router by wired LAN
to Internet
to LAN port
DSL or cable
modem with
internal router
(UPnP
compatible)
* To determine the type of your modem, check with your Internet service provider.
If you are already connected via NetAV,
disconnect before making the following
settings.
Select [External TV
tuner], and then select an
appropriate channel from
the pull-down list.
If the configuration above
is correct, each time you
click [Power], your TV
should turn on or off.**
• Connect to the
router by wired LAN
Connect to watch TV at home Connect to watch TV away from home
4 Enter the user ID and password, and
then click [OK].
User ID (User name) : lfx
Initial password: WebPassword
printed on the label
affixed to the side of
the base station.
To connect your computer to the base
station with a router, put the base
station into Setup Mode
(See STEP 2).
Start LocationFree™ Player, and then
click [Base Station Settings] in the
[Base Station Selection] window.
Your web browser starts, and the [Base Station
Settings] page opens.
1
5 Click [Easy Setup] in the settings
menu page. 6 If [Success] appears in the [NetAV
Check] page, click [Exit Setup].
The setup is complete.
z Tip
If [Setup Incomplete] appears in the [NetAV
Check] page, read the explanation on the
NetAV check page, and then make the
necessary settings.