American Audio Q-2411 - Manual (Page 12)

© American Audio ® - www.americanaudio.us - Q-2411™ Instruction Manual Page 12
channel input and the white represents the left channel input. Input volume will be controlled by the
channel two fader. The channel SOURCE SELECTOR SWITCH (4) must be in the "Phono 2/Aux 2"
position, to monitor any source connected to these jacks.
CHANNEL 2: LINE 2 INPUT JACKS - DO NOT CONNECT TURNTABLES TO THESE JACKS!
CD players, Tape Decks and other line level instruments may be connected to these jacks. The red
colored RCA jack represents the right channel input and the white represents the left channel input.
Input volume will be controlled by channel two fader. The channel SOURCE SELECTOR SWITCH (4)
must be in the "Line 2" position, to monitor any source connected to these jacks.
26. CHANNEL 3: PHONO 3/AUX 3 INPUT - The type of input must directly reflect the selected
mode of the LINE LEVEL SELECTOR SWITCH (23). Turntables equipped with MM pickup cartridge
(All DJ turntable use MM pick-up cartridges) may be connected to these jacks as long as the LINE
LEVEL SELECTOR SWITCH (23) is in the “PHONO 3” position. CD players, Tape Decks and other
line level instruments may only be connected to these jacks as long as the LINE LEVEL SELEC-
TOR SWITCH (23) is in the “AUX 3” position. Never connect line level instruments (CD players, tape
decks, etc.) to these jacks when the LINE LEVEL SELECTOR SWITCH (23) is in the “PHONO 3” posi-
tion, THIS MAY SERIOUSLY DAMAGE YOUR MIXER! The red colored RCA jack represents the right
channel input and the white represents the left channel input. Input volume will be controlled by the
channel three fader. The channel SOURCE SELECTOR SWITCH (4) must be in the "Phono 3/Aux 3"
position, to monitor any source connected to these jacks.
CHANNEL 3: LINE 3 INPUT JACKS - DO NOT CONNECT TURNTABLES TO THESE JACKS!
CD players, Tape Decks and other line level instruments may be connected to these jacks. The red
colored RCA jack represents the right channel input and the white represents the left channel input.
Input volume will be controlled by channel three fader. The channel SOURCE SELECTOR SWITCH
(4) must be in the "Line 3" position, to monitor any source connected to these jacks.
27. CHANNEL 4: LINE 4 INPUT JACKS - DO NOT CONNECT TURNTABLES TO THESE JACKS!
These Jacks are used for line level inputs. Connect CD players, Tape Decks and other line level
instruments may be connected to these jacks. The red colored RCA jack represents the right chan-
nel input and the white represents the left channel input. Input volume will be controlled by channel
four
fader. The channel SOURCE SELECTOR SWITCH (4) must be in the "Line 4" position, to moni-
tor any source connected to these jacks.
CHANNEL 4: LINE 5 INPUT JACKS - DO NOT CONNECT TURNTABLES TO THESE JACKS!
These Jacks are used for line level inputs. Connect CD players, Tape Decks and other line level
instruments may be connected to these jacks. The red colored RCA jack represents the right chan-
nel input and the white represents the left channel input. Input volume will be controlled by channel
four
fader. The channel SOURCE SELECTOR SWITCH (4) must be in the "Line 5" position, to moni-
tor any source connected to these jacks..
28. REC OUT - This is a low current unbalanced output source designed for various tape and CD
recorders. The Record Out (REC OUT) level is dictated by the CHANNEL FADER LEVEL (14), it is not
influenced by the MASTER VOLUME CONTROL (11).
29. RCA MASTER OUTPUTS - The Master Output includes a pair XLR BALANCED JACKS (31)
as well as a pair of RCA Unbalanced Jacks. The RCA jacks send a low current unbalanced output
signal. These jacks should only be used for shorter cable runs to signal processors or looping to
another mixer. For cable runs greater than 15 feet use the XLR BALANCED JACKS (31).
30. PLAYER CONTROL -
PLAYER 1 CONTROL - This jack is used to control the “Q-Start” function between the mixer
Q-2411™ REAR PANEL - CONTROLS AND FUNCTIONS CONT.