Panasonic TYWK42PR4W - Manual (Page 5)

5
English
5
4. Fit the insulation spacers to the plasma TV.
(1) Place the plasma TV unit face down on a blanket or other soft cloth that is clean and free of debris, and follow the
procedure below.
(2) Remove terminal covers (if fitted) from the plasma TV.
(3) Using a flathead screwdriver, remove the four caps from the plasma TV.
Note
• Carefully retain the removed terminal cover and caps in a
safe place. (They will be needed again later should it be
required to use the special-purpose stand or standalone
stand.)
Terminal cover
Caps
Flathead screwdriver
㇜
㇞ or ㇟
㇛
㇚
(4) Using the included Allen wrench ㇜ , fit the included
Allen head countersunk screws ㇞ or ㇟  dished toothed
washers ㇛ and insulation spacers ㇚ (4 sets) into the
holes from where the caps were removed. (See the
diagram at right.)
Refer to the page 46-50 for type selection of allen head
countersunk screws ㇞ , ㇟ .
The bolt should be securely tightened to the torque given
below.
(3 - 4 N•m)
5. Attaching the plasma TV to the wall-
hanging bracket and connecting the
wiring.
2
3
4
5
Top insulation
spacer
㊍ Red screw for open /
close fastening
Top notch
Lower hole
Lower
insulation
spacer
W
all surface
W
all surface
(1) Remove the red screws for open/close fastening (one each on
the left and right) ㊍ .
(2) Hook the insulation spacers on the top of the plasma TV over
the notches on the bracket, and allow the TV to hang from the
bracket.
(3) Pull the plasma TV body forward, as shown in the diagram at
right, and connect the wiring.
(4) After wiring is finished, slightly raise the plasma TV and insert
the insulation spacers at the lower back into the holes at the
base of the wall-hanging bracket.
(5) Lower the plasma TV into place.
Caution
• If the plasma TV is raised too far, there is a risk it may become
unhooked from the top of the bracket.
6. Fastening the plasma TV.
W
all surface
Hole for red
screw for
open / close
fastening
㊍ Red screw for open/
close fastening
Wall-hanging bracket
Fastening screw fitting
position
Plasma TV fastening screw
(1) Fit the included fastening screws in the indicated holes at the
sides of the wall-hanging bracket (left and right).
(2) Securely refit the red screws for open/close fastening (one
each on the left and right) ㊍ in the indicated holes on the
sides of the wall-hanging bracket.
The bolt should be securely tightened to the torque given below.
(1.2 - 1.5 N•m)
Note
• Be sure to fit the fastening screws on the left keep lifting upward.
and right to keep the plasma TV from falling off the wall-hanging
bracket.
7. Removal of plasma TV unit.
(1) Screw for plasma
TV unit fastening
(2) Insulation spacer
W
all surface
W
all surface
(1) Remove the screws for unit fastening (1 each on the left and
right) that are fitted to the wallhanging bracket sides.
(2) While lifting the bottom of the plasma TV unit, pull it towards
yourself.
(3) When the lower insulation spacers are freed, keep lifting
upward.
TY-WK42PR4W_TQZH993-3_4048.indb 5 TY-WK42PR4W_TQZH993-3_4048.indb 5 2008/04/07 11:56:37 2008/04/07 11:56:37