Panasonic ES8807 - Manual (Page 5)

9
the trimmer with the long brush (see
fig. 10). Clean the inner blades with
the short brush by moving it in the
direction in fig. 11 (A). Do not move
the brush in the direction in fig. 11
(B), as it will damage the inner blade,
and its cutting performance. Do not
use the short brush to clean the outer
foils.
Replacing shaving head
components
It is recommended that you replace
the system outer foil at least once a
year and the inner blade at least once
every 2 years to maintain your shav-
er’s cutting performance.
Replacing the system outer foil
(see fig. 8)
Squeeze the system outer foil re-
lease buttons and lift the system
outer foil upward to remove it. To in-
sert the new system outer foil, press
down until it snaps into place.
Replacing the inner blades
(see fig. 9)
Squeeze the system outer foil release
buttons and lift the system outer foil
upward to remove it. Remove the in-
ner blade one at a time by grasping
each firmly at both ends and pulling
straight away from the shaver.
Do not touch the metal parts of inner
blades.
To insert the new inner blade, hold
the blade one at a time at both ends
and press downward until each
snaps into the shaver.
For environmental protec-
tion and recycling of
materials
This shaver contains a Litium-ion
battery.
Please make sure that the battery is
disposed of at an officially assigned
location, if there is one in your
country.
How to remove the built-in
rechargeable battery before
disposal of the shaver
(see fig. 12)
WARNING:
Do not attempt to replace the bat-
tery for the purpose of reusing the
shaver. This could result in the risk
of fire or electric shock.
The battery in this shaver is not in-
tended to be replaced by consum-
ers. However, the battery may be re-
placed at an authorized service
center. The procedure described be-
low is intended only for removal of
the rechargeable battery for the pur-
pose of proper disposal.
1. Disconnect the power cord from
the shaver when removing the
battery.
2. Remove the bottom cover screw
(a).
3. Remove the trimmer (b).
4. Slide the back panel (c) and
remove it.
5. Remove the side panel (d).
6. Remove the three housing
screws (e).
7. Remove the housing (f).
8. Lift the battery (g) and remove it.
9 8
For wet shaving
Put a thin layer of shaving foam on
your face which works as a lubricant.
Shaving foam is the most suitable
among many other shaving aids (gel,
soap, cream, etc.). Do not put a thick
layer of shaving foam as it may af-
fect shaver’s performance. If the
shaving head is clogged with foam,
simply rinse it under running water.
Using the trimmer
(see fig. 6)
Slide the trimmer handle up to open
the trimmer.
Place the trimmer at a right angle to
your skin and move it downward to
trim sideburns.
Cleaning your shaver
(see fig. 7)
Warning – To prevent electric
shock or personal injury, discon-
nect the power cord from the
shaver before cleaning with water.
For cleanliness and convenience, we
recommend that you clean your
shaver with water and a liquid hand
soap. Regular cleaning will keep your
shaver in good condition while pre-
venting odors or bacteria from devel-
oping, and maintain the cutting per-
formance.
With the system outer foil in place,
apply some hand soap onto the outer
foil.
Push and hold the On/Off switch for
more than 2 seconds to activate the
turbo mode for “sonic” vibration
cleaning.
At the same time, the lamps of the
Battery capacity monitor illuminate
randomly.
Pour some water over the outer foil.
After about 20 seconds, it will be
automatically turned off, or you can
turn it off by pushing the On/Off
switch.
Remove the system outer foil and
push the On/Off switch more than
2 seconds to activate the turbo mode
for “sonic” vibration cleaning and
clean it with running water.
Wipe off any moisture from the
shaver with a dry cloth and dry it with-
out the system outer foil.
Lubrication
(see fig. 13)
To maintain shaving comfort for a
long time, it is recommended that
the oil provided with the shaver is
used.
1. Switch off the shaver.
2. Apply one drop of oil to each of
the outer foils.
3. Raise the trimmer and apply a
drop of oil.
4. Switch the shaver on, and run it
for approximately five seconds.
5. Switch off the shaver, and wipe
off any excess oil from the outer
foils with a soft cloth.
Brush cleaning
Squeeze the foil frame release but-
tons and lift the foil frame upward to
remove it (see fig. 9). Remove the in-
ner blades one at a time by grasping
it firmly at both ends and pulling it
straight away from the shaver. Clean
the outer foils, the shaver body and
8
P006-123_ES8807_EU 06.8.9 13:11 ページ 8