Scarlett SC-1223 - Manual (Page 4)

www.scarlett-europe.com SC-1223 4
GB INSTRUCTION MANUAL
IMPORTANT SAFEGUARDS
· Please read these operating instructions carefully
before connecting your kettle to the power supply, in
order to avoid damage due to incorrect use.
· Before first switching on check that the voltage
indicated on the rating label corresponds the mains
voltage in your home.
· Incorrect operation and improper handling can lead
to malfunction of the appliance and injuries to the
user.
· For home use only. Do not use for industrial
purposes.
· Always unplug the appliance from the power supply
when not in use.
· Keep the base unit away from water and protect
from splashes.
· Do not immerse the unit, cord or plug in water or
other liquids. If it has happened, remove the plug
from the wall socket immediately and an expert
should check the unit before using it again.
· Do not operate the appliance if the cord or the plug
is damaged or, if the appliance has been otherwise
damaged. In such cases take the appliance to a
qualified specialist for check up and/or repair if
necessary.
· Ensure that the cord does not hang over sharp
edges and keep it away from hot surfaces.
· To disconnect appliance from the power supply pull
it out by the plug only, not by the cord.
· Place the appliance on a dry stable non-hot surface,
away from hot objects (e.g. hotplates); do not place
under curtains and shelves.
· You should never leave the appliance not
supervised during use.
· Keep the appliance away from children.
· Use the kettle only with the base unit supplied, and
do not use the base unit for any other purposes.
· Never take off the kettle from its base unit while in
operation. Switch the appliance off first.
· Close the lid properly before switching on.
Otherwise, the appliance will not switch off
automatically and the hot water may overflow.
· The kettle is for heating water only, not for any other
purposes and liquids.
BEFORE USING FOR THE FIRST TIME
· Remove all packing materials and sticker from the
kettle.
· Place the filter.
· Fill the kettle with cool water up to the maximum
level mark and boil it. Empty the kettle. Repeat this
operation. The appliance is ready for use.
INSTRUCTION FOR USE
FILTER PLACING
· Open the lid.
· Place the filter between two grooves near the spout
at the front of the kettle.
· Ensure that the filter is pressed properly down to the
bottom of the grooves, and then close the lid.
NOTE: Never leave the filter loose in the kettle. Never
remove the filter while the kettle contains hot water.
FILLING
· Take the kettle off from the base unit.
· You can fill the kettle with water via the spout or neck
with opened lid.
· Do not fill with less than 0.5 l of water (less than
MIN mark) to prevent the kettle from operating dry
and more than 1.7 l (up to MAX mark) to avoid
overfilling and water spilling out during the boiling.
SWITCHING ON
· After filling with water, place the kettle on the base
unit.
· Connect the plug to the power supply and push
On/Off switch. The appliance will begin to operate
and indicator will light.
SWITCHING OFF
· When water begins to boil, the kettle will switch off
automatically and indicator light will go off.
NOTE: This appliance has a safety system, which
automatically switches off heating element if the
appliance inadvertently has been switched on when
empty, or if it operates dry. In this case let the appliance
cool down 10 minutes before filling with water again.
SWITCHING ON AGAIN
· The kettle can be switched on again after cooling
during 15-20 seconds, while the kettle has been
switched off automatically.
CARE AND CLEANING
· Always remove the plug from the socket and let the
appliance cool down completely.
· Clean the outside of the kettle and the base unit with
a soft damp cloth, then wipe with a dry cloth. Do not
use any abrasive materials.
· Remove scale regularly, using special descaling
agents, available at the market, following given
instructions.