Aube Technologies Pilot-wire Programmer TH134 - Manual (Page 3)

TH134 400-134-000-A 1/27/05 3/4
Whenever an order is received via the remote input, it becomes the
active order for all 3 zones. To know which orders can be initiated
by the energy manager, the phone controller or the home automa-
tion system, see the table on page 1. The is displayed when
signals are received via the remote input.
Orders received via the remote input have priority over orders initi-
ated via the TH134 programmer. However, you can bypass the
remote input order for each zone for 2 hours. At the end of the 2
hours, the remote input order becomes active again.
n
Select the zone using the Zone button. (Press for 3
seconds to select all 3 zones.)
o
Press the desired order button.
The icon flashes during the bypass.
The same schedule is used by default for all 3 zones as shown
below.
Use the following procedure to select the order and the start time for
each of the 4 programs for each zone. The settings of each pro-
gram will be the same for each day. However, you can then select
which programs to be executed for each day and for each zone.
n
Press the PGM to start programming.
o
Select the zone using the Zone button. (Press for 3
seconds to select all 3 zones.)
p
Select the program using the PGM button.
q
Set the program start time.
r
Select the mode by pressing the corresponding button.
s
Repeat steps 3 to 5 for the remaining programs for the selected
zone.
t
Go to step 2 if you wish to select another zone.
u
Press to exit programming.
TH134 will automatically exit programming if no button is
pressed for the last 60 seconds.
When selecting the number of programs,
n
Press the MAN/AUTO button for 3 seconds
until PPd is displayed.
o
Select the zone using the ZONE button.
(Press for 3 sec. to select all 3 zones.)
p
Press MAN/AUTO until the desired day is
displayed.
q
Set the number of programs for the selected
day using the
buttons. The options are:
• 4 (to select all 4 programs)
• 2 (to select program 1 and 4 only)
• 0 (no program is selected for that day)
If no program is selected for a particular day, TH134 uses
the order of the last program until the start of the next program.
r
Repeat steps 3 and 4 for the each remaining day.
s
Go to step 2 if you wish to select another zone.
t
Press to exit.
Enter your settings in the following table.
Preprogramm ed Sched ul e Preprogramm ed Sched ul e Preprogramm ed Sched ul e Preprogramm ed Sched ul e Preprogramm ed Sched ul e Preprogramm ed Sched ul e Preprogramm ed Sched ul e Preprogramm ed Sched ul e Preprogramm ed Sched ul e Preprogramm ed Sched ul e Preprogramm ed Sched ul e Preprogramm ed Sched ul e Preprogramm ed Sched ul e
C √ √ √ √ √ √ √
S √ √ √ √ √
C √ √ √ √ √
S √ √ √ √ √ √ √
4 4 4 4 4 2 2
Sch edule custom ization Sch edule custom ization Sch edule custom ization Sch edule custom ization Sch edule custom ization Sch edule custom ization Sch edule custom ization Sch edule custom ization Sch edule custom ization Sch edule custom ization Sch edule custom ization Sch edule custom ization Sch edule custom ization
Wake-up time
Every day
Leave for work
Monday to
Friday
Return home
Monday to
Friday
Sleep time
Every day