AeroBed All-Terrain - Manual

7986 Rev 12/09
109 Pump
Instruction Manual
This is the closed position. Open Air Release Valve Close Valve Using 2 Thumbs
INFLATION
NOTE: BED MUST BE AT ROOM TEMPERATURE PRIOR TO INFLATING OR IT MAY CAUSE AIR LEAKS.
1. Place your rolled-up bed on the floor or other surface free of obstructions or sharp objects.
2. Make certain the Quick Air Release Valve located at the head of the bed is closed. If the Air Release Valve is open, close it by using 2 thumbs to
push cover and snap into valve. Be careful to avoid pushing valve cover to the right or left as it snaps into the valve opening.
3. Remove the protective plastic cap from the valve by turning counter clockwise. Open the protective rubber cap at the end of the pump. Press the
mouth of the pump into position on the inflation/Release Valve and turn clockwise until it locks (see figure C).
4. A one-quarter turn clockwise automatically starts inflation.
5. At approximately 60 seconds, a high pitch whine of the pump will signal the bed is inflated to full (firmest) capacity. Bed will not over-inflate.
8. Detach pump by turning counter clockwise. Lie on bed and check the firmness. If you want your bed to be softer, depress the button in the center
of the valve. If the bed becomes too soft, reattach the pump and reinflate the bed until the desired level of firmness is achieved (see figure D).
IMPORTANT: Be sure to close the protective valve cap after inflation.
RECHARGEABLE Ni-Cd PUMP
IMPORTANT: PUMP MUST BE CHARGED FOR 24 HOURS PRIOR TO THE FIRST INFLATION. Use the AC adaper to charge your pump
for 24 hours. For maximum performance, be sure to fully discharge pump before recharging. After initial charge and use, charge pump for 12 HOURS
at a time. Charging your pump for periods shorter or longer than 12 hours will substantially decrease the life of your Ni-Cd pump. In an emergency, a
3 hour charge will provide one inflation, however, continued charging for 3 hour periods will substantially decrease the life of your Ni-Cd pump.
IMPORTANT: ALWAYS store pump and charger in a cool, dry place. DO NOT allow pump or charger to get wet. Allowing pump and/or charger to
get wet will void your warranty.
TO CHARGE / RECHARGE:
a) First, remove pump and charger from box (see figure A).
b) Second, remove tiny rubber plug from hole on the back of the pump. Insert the charger’s mini-plug in the hole (see figure B).
c) Third, plug the charger unit into any standard 110V (or 220V depending on your local service) electrical outlet and let it charge for 12 hours
(24 hours on initial charge).
NOTE: For best pump performance, you must completely drain the charge from your pump prior to recharging. For directions, see discharge section below.
Prior To Inflation:
a) Unplug the pump after it has been charged for 12 hours (24 hours on initial charge).
b) Remove charger unit from the electrical outlet and the mini-plug from the pump.
c) Re-insert the tiny rubber plug into the hole on the back of the pump.
NOTE: Pump will not run while charger is plugged into an electrical outlet.
To Discharge:
a) Place pump on valve as if to inflate product.
b) Allow pump to run until the pump motor dies down.
NOTE: When properly used, your pump will hold a full charge for approximately 90 days. When storing pump for longer than 90 days, fully discharge
and recharge pump every 120 days. This will help maximize pump life.
TO USE PUMP INSTANTLY WITHOUT HAVING TO RECHARGE THE NI-CD BATTERIES:
a) First, remove the tiny rubber plug from hole on the back side of the pump.
b) Second, insert the 12-volt DC adapter mini-plug into the hole.
c) Third, plug the DC power cord into a standard 12-volt DC automobile cigarette lighter or accessory 12-volt outlet and turn ignition to the accessory position.
Do not operate pump while engine is running.
d) When the bed is fully inflated, detach pump and unplug the 12-volt adapter from the lighter.
WARNING: Do not leave the pump plugged into the cigarette lighter or 12-volt DC outlet, doing so could damage the life of the Ni-Cd batteries. PUMP
SHOULD ONLY BE USED WITH AERO ADAPTERS PROVIDED. DO NOT USE WITH ANY OTHER ADAPTERS. To avoid against risk of fire, electric
shock or injury to persons, read all instruction before using.
CAUTION! Do not incinerate or disassemble this pump, it could result in an explosion or release of toxic materials. Do not short circuit the pump, it may
cause burns.
IMPORTANT: PUMP CONTAINS NICKEL-CADMIUM BATTERIES. BATTERIES MUST BE RECYCLED OR DISPOSED OF PROPERLY.
A REPAIR PATCH CAN BE ORDERED AT WWW.AEROBED.COM OR BY CALLING OUR CUSTOMER SERVICE AT 1-888-462-4468.
IMPORTANT SAFETY INFORMATION AND WARNINGS
SAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT
IMPORTANT: Preparation of your AeroBed product requires no tools. Use of tools may damage your bed.
WARNING: This is an electrical product – not a toy. To avoid risk of fire, burns, injury, or shock:
- Always unplug from outlet when not in use and before cleaning.
- Close supervision is necessary when this product is used by or near children, invalids, or disabled persons.
- Use this product only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
- Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water.
- Keep the cord away from heated surfaces.
- Never operate the product with the air openings blocked. Keep the air openings free of lint, hair, and the like.
- Never drop or insert any object into any opening.
- To disconnect, turn all controls to off position, then remove plug from outlet.
WARNING: Product is for indoor use only. Do not use outdoors. For household / residential use only.
WARNING: This furnishing has not been evaluated for flammability or cigarette ignition resistance.
ADDITIONAL WARNINGS:
- Bed supports a maximum weight of 300 lbs. per person.
- This is not a water toy. Use as a mattress only.
- This bed is not designed for use by children under 3 years of age or any persons with limited mobility as they could suffer serious or fatal injury through suffocation, falling from or
rolling off the bed or becoming trapped.
- Use on flat surfaces only. Bed may tip over on uneven surfaces.
- Inflate bed fully. Partially inflated mattresses can cause suffocation.
- Remove all sharp objects from area where bed will be set up and used. Do not use this bed on abrasive surfaces or near pointed/sharp items or surfaces. Bed may puncture.
- Do not step or jump on bed or use as a trampoline.
- This bed is made of plastic and therefore may melt or burn if it comes in contact with any flame or heat source. Do not place it near or against heaters, open flame, or other hot objects.
- Unplug product when not in use.
- Pump is not intended for continuous use. Pump may stop working or overheat if it is used for extended periods of time. Do not use pump continuously for more than 4 minutes.
To avoid excessive heat build-up in the pump, let it rest for 5 minutes between complete inflation cycles.
- Do not attempt to disassemble, repair, or service the pump. No serviceable parts are contained inside.
Contact Aero Products International, Inc. at 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173, 1-888-462-4468 for repair or servicing information.
Thank you for joining the AeroBed ® family by purchasing one of our products. You can expect top-notch quality, innovation and imagination from every AeroBed product.
You are about to enjoy the comfort of an AeroBed product. It is your responsibility to read and always follow the safety, care and maintenance instructions for your new
AeroBed product. Always instruct and supervise others on your bed’s proper use, maintenance and safety.
A
B
C
D