Aube Technologies Aube TI062 - Manual (Page 2)

TI062 400-062-000-B 2008-07-04 2/2
4.5 Sunset/sunrise mode
When the timer is plugged to an outlet
exposed to daylight, this mode is used to turn
lights on at sunset and turn them off at sunrise.
The lights turn on when the darkness threshold
is reached. (The icon flashes when the
darkness threshold is not yet reached.) When
the timer will detect light, the lights will turn off.
NOTE: Ensure that the timer is positioned such that the light sensor
is pointing to an area that is undisturbed by car lights, outdoor lights,
etc.
4.6 Temporary Override
You can press the On/Off button at any time to apply or cut power to
the appliance. If you derogate from the state in which the timer is
supposed to be, the new state (On or Off) will flash to show that it is
temporary. The override remains in effect until you press the On/Off
button or until the start of the next on or Off time.
n
Hold the On/Off button for 3 seconds to
enter the menu.
o
Press the button once. The Time
menu will flash.
p
Press the On/Off button to display the
time format options. The selected
format will flash. Press the or
button to switch format.
q
Press the On/Off button. The hour
setting will flash. Press the or
button to set the hour.
r
Press the On/Off button. The minutes
setting will flash. Press the or
button to set the minutes.
s
Hold the On/Off button any time for 3
seconds to exit the menu.
NOTE: The timer automatically returns to its
normal display if you do not press any
button for 60 seconds.
n
Hold the On/Off button for 3 seconds
to enter the menu.
o
Press the button twice. The Prog
menu will flash.
p
Press the On/Off button. The hour
setting will flash. Press the or
button to set the hour for the program
start time.
q
Press the On/Off button. The minutes
setting will flash. Press the or
button to set the minutes for the
program start time.
r
Press the On/Off button. The hour
setting will flash. Press the or
button to set the hour for the program
end time.
s
Press the On/Off button. The minutes
setting will flash. Press the or
button to set the minutes for the
program end time.
t
Press the On/Off button to display the
temperature format options. The
selected format will flash. Press the
or button to switch format.
u
Press the On/Off button to display the
temperature threshold. Press the or
button to display the desired
threshold.
v
Hold the On/Off button any time for 3
seconds to exit the menu.
NOTE: The timer automatically returns to its normal display if you do
not press any button for 60 seconds.
To test if the light sensor is working properly:
n
Place the timer in automatic mode with darkness threshold or in
sunset/sunrise mode.
o
Position the timer such that it be exposed to daylight.
p
Check that the icon flashes to indicate the sensor has
detected light.
q
Place your finger on the sensor.
r
Check that the icon stops flashing after approximately 40
seconds to indicate the sensor has not detected light.
s
Remove your finger.
t
Check that the icon resumes flashing after approximately 40
seconds.
To return to factory settings, simultaneously press both
On/Off and buttons and hold. The software version will
appear for 5 seconds. RST will appear for the next 5
seconds. Release the buttons only when all segments
appear on the screen. The timer is now reset.
During a power outage, the screen is blank. If the outage lasts more
than 4 hours (at 25 °C / 77 °F), when power will be back, the clock
will be reset (0:00) and will start ticking again. Therefore, the timer
can still apply or cut power to the controlled appliance, however the
on/off times will be shifted.
Supply: 120 VAC, 60 Hz
Maximum load: 15 amps, 1 HP
Operating temperature: -40 to 50 °C (-40 to 122 °F) [NOTE: The
display is illegible below -20°C (-4°F)]
Charging time: minimum of 8 hours
Data protection: Most settings are saved at all times. Only the clock
must be set if the timer was without power for more than 4 hours (at
25 °C / 77 °F).
Program: 1 on setting and 1 off setting. The same settings are
repeated every day.
Approval: UL (c UL us)
AUBE warrants this product, excluding battery, to be free from defects in the workman-
ship or materials, under normal use and service, for a period of three (3) years from the
date of purchase by the consumer. If at any time during the warranty period the product is
determined to be defective or malfunctions, AUBE shall repair or replace it (at AUBE's
option).
If the product is defective,
(i)
return it, with a bill of sale or other dated proof of purchase, to the place from
which you purchased it, or
(ii) contact AUBE. AUBE will make the determination whether the product should be
returned, or whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This warranty shall not
apply if it is shown by AUBE that the defect or malfunction was caused by damage which
occurred while the product was in the possession of a consumer.
AUBE's sole responsibility shall be to repair or replace the product within the terms stated
above. AUBE SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND,
INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING,
DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS
OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some provinces, states
or regions do not allow the exclusion or limitation of incidental or consequential damages,
so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE MAKES ON THIS
PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WAR-
RANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS
HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS WARRANTY. Some
provinces, states or regions do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary
from one province, state or region to another.
705 Montrichard Avenue
Saint-Jean-sur-Richelieu, Quebec
J2X 5K8
Canada
Tel.: (450) 358-4600
Toll-free: 1-800-831-AUBE
Fax: (450) 358-4650
Email: [email protected]
For more information on our products, go to
www.aubetech.com
r
Setting the Clock 5.
s
Setting the Program and Temperature 6.
t
Testing the Light Sensor 7.
u
Reset to Factory Settings 8.
v
Power Outage 9.
w
Technical Specifications 10.
;
Warranty 11.
Technical Assistance 12.
400-062-000-B ENG.fm Page 2 Friday, July 4, 2008 9:37 AM