CatEye HL-EL540 [Econom Force] - Manual

SPECIFICATIONS
Light source ............ High-intensity white LED x 1
Battery .................... AA alkaline battery x 4
Operating time ........ Hi : Approx. 2 hours, Low : Approx. 9 hours,
Flash : Approx. 30 hours
Temperature range .. 14˚F – 104˚F (-10˚C – 40˚C)
Dimensions/weight ... 4-1/2” x 2-13/64” x 2-3/32” (114 x 56 x 53 mm)
/ 8 oz (227 g) (Including batteries)
The specifi cations and design are subject to change without notice. *
BATTERY HEADLIGHT
HL-EL540
Pat. and Design Pat. Pending
Copyright© 2012 CATEYE Co., Ltd.
EL54-120123 066640832 3
INTRODUCTION
Before using the product, please thoroughly read
this manual and keep it for future reference.
CAUTION!
Before your trip, please make sure the light is •
fi rmly mounted to the bracket, it lights up, and
the light is not blocked by baggage, etc.
Mount the light unit more than 7 cm away •
from the wireless meter. When it is mounted
too close, the transmission may be affected
adversely.
This product is water-resistant under normal •
daily use and can be used in the rain. However,
do not intentionally submerge it in water.
If the light unit or parts become dirty with mud, •
etc., clean with a soft cloth which is moistened
with mild soap. Never apply paint thinner,
benzine or alcohol; damage will result.
COMPONENTS
HOW TO REPLACE BATTERY
HOW TO MOUNT
HOW TO USE
*1
NO!
Close
Open
3
1
2
2
1
3
CO.,LTD.
2-8-25, Kuwazu, Higashi Sumiyoshi-
ku, Osaka 546-0041 Japan
Attn: CATEYE Customer Service
Phone : (06)6719-6863
Fax : (06)6719-6033
E-mail : [email protected]
URL : http://www.cateye.com
[For US Customers]
CATEYE AMERICA, INC.
2825 Wilderness Place Suite 1200,
Boulder CO80301-5494 USA
Phone : 303.443.4595
Toll Free : 800.5CATEYE
Fax : 303.473.0006
E-mail : [email protected]
SPARE PARTS
OPTION PARTS
CHA-2.2AH-4.8V
5338827N
FlexTight™ bracket (H-34N)
Special nickel-hydride
rechargeable battery x 4
(Ni-MH 2.2Ah GP220AAH)
UL : 5336760
UK : 5336761
EC : 5336762
AS : 5336763
JP : 5336764
ENG
LIMITED WARRANTY
2-year Warranty: Light unit only
CatEye products are warranted to be free of defects from materials
and workmanship for a period of 2 years from original purchase. If
the product fails to work during normal use, CatEye will repair or re-
place the defect at no charge. Service must be performed by CatEye
or an authorized retailer. To return the product, pack it carefully and
enclose the warranty certifi cate (proof of purchase) with instruction
for repair. Please write or type your name and address clearly on the
warranty certifi cate. Insurance, handling and transportation charges
to CatEye shall be borne by person desiring service. For UK and
REPUBLIC OF IRELAND consumers, please return to the place of
purchase. This does not affect your statutory rights.
Turn the lock cap on the back of the light 1
counterclockwise to remove.
Press the switch slowly, and pull out the
2
inner unit from the front.
Install the lower battery fi rst. Remove the
3
upper battery fi rst by pressing the arrowed
point as shown.
After replacement, check that the two rubber
4
gaskets for the inner unit are in place, place it
into the body, and fi x it with the lock cap.
CAUTION!:
To pull out the inner unit from the light, be •
sure to hold the lens. Otherwise, the inner
unit may fall out and become damaged.
Do not use in combination with new and old •
batteries, or different types of batteries.
Be sure to install batteries in the correct •
direction.
Install the two rubber gaskets correctly to •
maintain waterproof features.
Remove and store batteries when you will •
not use the light for a long period of time.
Otherwise, batteries may leak liquid, which
may result in failure.
Wind the bracket strap around the handlebar, 1
and put the strap through the opening.
Screw the dial into the bracket to secure it
2
temporarily.
Insert the light unit to the bracket until it *
clicks, and adjust the beam angle.
(Refer to “HOW TO MOUNT THE LIGHT”)
Securely tighten the dial, and cut off any 3
excess bracket strap.
To remove the light unit, pull out it forward *
while pressing the button.
To re-adjust the beam angle, loosen the dial *
enough to move the bracket, and securely
tighten it after adjustment.
CAUTION!:
Be sure to tighten the dial by hand. When •
you tighten it too hard with a tool, the screw
thread may be stripped.
Check the dial and screw (*1) on the bracket •
periodically, and use them without any
loosening.
Round off the cut edge of the bracket strap •
to prevent injury.
Switch operation
(switching the lighting mode)
The ON/OFF and lighting modes are selected
using a switch.
Standard operating time
Hi : Approx. 2 hours
Low : Approx. 9 hours
Flash : Approx. 30 hours
*2 When returning from Flash to ON (Hi or Low),
it returns to the ON mode used previously.
Remaining battery capacity
When the switch (indicator) lights up, the
remaining battery level is low. Replace with
new batteries.
ON ↔ OFF : Long press
Hi ↔ Low : Single press
Flash : Quick double press
(Flash even from OFF)
Lock cap
Inner unit
Switch
Rubber gasket
How to remove
batteries
Dial Rubber pad Bracket
Strap
Light unit
FlexTight™
bracket (H-34N)
AA alkaline
battery x4
HOW TO MOUNT THE LIGHT
Release
button
Screw
Press the lens
side of the upper
battery.
5341891
Switch (indicator)