American Electric Lighting Series 11 Package - Manual

INSTALLATION INSTRUCTIONS
SERIES 11 L PACKAGE
American Electric Lighting a division of Acuity Lighting Group, Inc. Conyers, GA
DRAWING NO. B63400 REV R (FRONT) ©2003 ACUITY LIGHTING GROUP, INC. PART NUMBER 057-71-12477
SCREW AND FIXTURE AS SHOWN ON BACK.
ALT: CONNECT GROUNDING LEAD BETWEEN GROUND
ON AT DUSK,OFF AT DAWN.
THE FIXTURE IS NOW READY TO OPERATE AUTOMATICALLY
SEVERAL MINUTES BEFORE THE LIGHT EXTINGUISHES.
WILL TURN OFF. AGAIN, THERE MAY BE A DELAY OF
2. REMOVE THE BOX FROM THE PHOTOCONTROL AND IT
ON ALL DAY AND ALL NIGHT.)
(A DEFECTIVE PHOTOCONTROL WILL KEEP THE LIGHT
THE PHOTOCONTROL OR THE FIXTURE IS DEFECTIVE
A CAUSE FOR CONCERN. IT DOES NOT MEAN THAT
TURN ON. THIS IS NORMAL, AND IT IS NOT
THEN, AFTER 3 TO 5 MINUTES DELAY, IT WILL
THE LIGHT ON AND IN A FEW MINUTES TURN OFF.
NOTE: SOME MODELS OF PHOTOCONTROL WILL TURN
FOR IT TO ATTAIN FULL BRILLIANCE.
AND IT WILL TAKE APPROXIMATELY 10 MINUTES
THE FIXTURE SHOULD LIGHT WITHIN 5 MINUTES,
MATERIAL TO COVER THE PHOTOCONTROL.)
FOIL OR ANY OTHER ELECTRICALLY CONDUCTIVE
WITH THE BOX THAT IT CAME IN. (NEVER USE ALUMINUM
DURING DAYLIGHT, COVER THE PHOTOCONTROL
SUPPLY. TO CHECK THE OPERATION OF THE FIXTURE
1. ENERGIZE THE FIXTURE BY TURNING ON THE ELECTRICAL
TESTING
MOUNTING ARM
CLAMP
CARRIAGE BOLT
NUT
WASHER. TIGHTEN ALL SCREWS SECURELY.
ING BOLT BETWEEN THE MAST ARM BRACKET AND
CONNECTING THE GROUNDING LEAD AROUND THE GROUND-
AT THE BASE OF MAST ARM. THE 24" MAST REQUIRES
SCREW BETWEEN THE SCREW HEAD AND CUP WASHER,
SERVICE BY HOOKING IT AROUND THE GREEN GROUNDING
PLICATION CONNECT THE GROUNDING LEAD FROM THE
TO THE BLACK SERVICE WIRE. FOR THE 18" MAST AP-
SERVICE WIRE, CONNECT THE BLACK FIXTURE WIRE
2. CONNECT THE WHITE FIXTURE WIRE TO THE WHITE
REQUIREMENTS.
ELECTRICAL CODES FOR WIRING AND GROUNDING
1. BEFORE WIRING THIS FIXTURE, CONSULT THE LOCAL
WIRING
ENGAGED, AND TIGHTEN THE FITTER BOLTS "A" SECURELY.
THE FIXTURE ONTO THE MOUNTING ARM UNTIL IT IS FULLY
1. FEED THE FIXTURE WIRES THROUGH THE MOUNTING ARM, SLIDE
MOUNTING THE FIXTURE
2. SCREW BULB INTO BULB SOCKET UNTIL BULB IS FIRMLY SEATED.
THE BULB SOCKET. (SEE ILLUSTRATION.)
SECURE THE OPTICAL ASSEMBLY TO THE BRACKET THAT HOLDS
SCREWS WITH WASHERS THROUGH THE HOLES IN THE REFLECTOR.
1. FASTEN OPTICAL ASSEMBLY TO FIXTURE BY PLACING THE TWO
MUST BE LOCKED IN FOR FOR SATISFACTORY OPERATION.
ENGAGEMENT BY PULLING UP ON THE PHOTOCONTROL, AS IT
LOCKED INTO POSITION. IT IS ADVISABLE TO TEST THE
PUSH IT FIRMLY, AND TWIST IT CLOCKWISE UNTIL IT IS
INSERT THE PHOTOCONTROL INTO THE RECEPTACLE/SOCKET,
WITH THE LARGE OPENING IN THE RECEPTACLE/SOCKET.
2. POSITION THE PHOTOCONTROL SO THE LARGE PRONG IS ALIGNED
THE MOUNTING SURFACE. TIGHTEN THE POSITION SCREW.
SOCKET SO THAT THE ARROW ON ITS TOP POINTS AWAY FROM
CONTROL RECEPTACLE/SOCKET AND ROTATE THE RECEPTACLE/
1. LOOSEN THE POSITIONING SCREW IN THE TOP OF THE PHOTO-
INSTALLING THE PHOTOCONTROL
THESE SCREWS SECURELY.
PLACE, USING THE FOUR LAG SCREWS SUPPLIED. TIGHTEN
3. FASTEN THE MOUNTING ARM AND CLAMP ASSEMBLY INTO
THE MARKED POSITIONS.
3/16" DIAMETER HOLES INTO THE MOUNTING SURFACE AT
MARK THE FOUR MOUNTING HOLE POSITIONS. DRILL FOUR
THE MOUNTING ARM AND CLAMP ASSEMBLY INTO PLACE AND
CATION. AFTER DETERMINING A SUITABLE LOCATION, HOLD
MOUNTING SCREWS ARE NOT FURNISHED FOR THIS APPLI-
TO A STURDY METAL SURFACE, OR TO A METAL POLE, BUT
VERTICAL WOOD STUD. THE FIXTURE CAN ALSO BE BOLTED
MOUNTING, TWO OF THE FOUR SCREWS SHOULD ENTER A
SOUND WOOD THAT IS SECURELY ANCHORED. FOR WALL
2. THE LAG SCREWS MUST BE MOUNTED INTO STRUCTURALLY
TO THE MOUNTING SURFACE IF NECCESARY.
IT SECURELY. BEND THE LEGS OF THE CLAMP TO CONFROM
ONTO THE SHORT END OF THE MOUNTING ARM, TIGHTENING
IN THE SIDE OF THE CLAMP.INSTALL THE ASSEMBLED CLAMP
CARRIAGE BOLT AND HEX NUT THROUGH THE SQUARE HOLES
1. HOOK THE TWO CLAMP PIECES TOGETHER AND FASTEN THE
INSTALLING THE MOUNTING ARM
INSTALLING THE OPTICAL ASSEMBLY & LAMP
GROUND SCREW
AND CUP WASHER
CAUTION
THE MOUNTING ARM IS NOT DESIGNED TO SUPPORT THE
WEIGHT OF A PERSON. MAKE SURE 1" OF MOUNTING ARM
EXTENDS BEYOND THE BRACKET (SEE ILLUSTRATION)
!
THE FIXTURE IS SUPPLIED WITH A STANDARD LAMP, WHICH
CAN CAUSE SERIOUS SKIN BURNS AND EYE INFLAMMATION IF
IT IS OPERATED WHEN THE OUTER GLASS JACKET OF THE LAMP
IS BROKEN. IF THE GLASS SHOULD BREAK DURING OPERATION,
DISCONNECT THE POWER TO THE FIXTURE AND REPLACE THE
DEFECTIVE LAMP IMMEDIATELY. TO INSTALL THE LAMP, SCREW
IT INTO THE LAMP SOCKET UNTIL IT IS FIRMLY SEATED
WARNING
!
DISCONNECT POWER BEFORE INSTALLING OR
SERVICING THE FIXTURE
WARNING
!
CAUTION
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE
INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL
AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE
INTERPRETATION, CONSULT LOCAL CODE AUTHORITY. BEFORE
INSTALLING VERIFY THAT THE SUPPLY VOLTAGE MATCHES THAT
REQUIRED BY THE FIXTURE AS SPECIFIED ON THE DATA LABEL.
!
DO NOT LEAVE THE PHOTOCONTROL COVERED WITH THE BOX,
OR OTHER MATERIAL, FOR SEVERAL HOURS AS DAMAGE TO THE
PHOTOCONTROL, OR TO THE FIXTURE, MAY RESULT
CAUTION
!