American Electric Lighting 125 new - Manual

125 SERIES HORIZONTAL LUMINAIRE
INSTALLATION INSTRUCTIONS
American Electric Lighting a division of Acuity Lighting Group, Inc. Conyers, GA
DRAWING NO. B62015 REV C ©2004 ACUITY LIGHTING GROUP, INC. PART NUMBER 057-71-62015
ADJUSTING SCREW
SOCKET
SOCKET GASKET
REFLECTOR BRACKET
SOCKET BRACKET
A
B
C
D
NOTE: *Available with coated lamp only
**Requires socket spacer
POLYCARB 175/250W MERC/MH II MSC 3** C
D 3 III MSC 400W MERC/MH DROP LENS
C 3
A 1
A 2
C 2
C 3
A 3**
C 2
D 3
A
A
A
3
2**
3
2
1
3
3**
3
2
D
A
C
A
A
C
LENS LAMP TYPE VERT HORZ
III MC
II MC
IV MSC
III MS
II MC
III MSC
II MC
III MSC
II MSC
III MSC
I MSC
II MSC
III MC
III MC
II MC
III MSC
II MSC
35-150W HPS
35-150W HPS
35-150W HPS
200-400W HPS
200-400W HPS
200-400W HPS
200-400W HPS
200-400W HPS
200-400W HPS
200-400W HPS
175/250W MERC/MH
175/250W MERC/MH
175/250W MERC/MH
400W MERC/MH
400W MERC/MH
400W MERC/MH
400W MERC/MH
DROP LENS
DROP LENS
DROP LENS
DROP LENS
DROP LENS
DROP LENS
DROP LENS
DROP LENS
FLAT LENS
FLAT LENS
FLAT LENS
FLAT LENS
FLAT LENS
POLYCARB
POLYCARB
POLYCARB
POLYCARB
POLYCARB 175/250W MERC/MH III MC 3** A
TERMINAL BLOCK. VERIFY THAT SUPPLY VOLTAGE IS CORRECT
AS NOTED ON THE TERMINAL BLOCK LABEL. REFER TO THE WIRING
INFORMATION AND RATINGS.
DIAGRAM AND THE DATA ON THE BALLAST FOR CONNECTION
CLEAN OR REPLACE AS DESIRED.
SUPPORT THE REFRACTOR AT ALL TIMES. REMOVE REFRACTOR
HOUSING". ROTATE THE REFRACTOR LATCH BEING CAREFUL TO
OPEN THE LOWER DOOR AS OUTLINED UNDER "REMOVE LOWER
REFRACTOR REPLACEMENT
DETERGENT AND RINSED WITH CLEAN WATER TO MAINTAIN EFFICIENCY.
THE OPTICAL ASSEMBLY SHOULD BE CLEANED WITH A MILD
MAINTANCE AND CLEANING
SOCKET TO ITS NEW LOCATION AND REASSEMBLE.
SOCKET TO THE ADJUSTABLE BRACKET AND MOVE THE
OF THE GASKET. REMOVE THE TWO SCREWS HOLDING THE
SOCKET BRACKET SLIGHTY AND SLIDE THE SOCKET OUT
THE SOCKET SCREWS HOLDING SOCKET. NEXT SPREAD THE
START BY REMOVING THE TWO SOCKET WIRES AND THEN
REMOVAL OF THE SOCKET FROM THE SOCKET BRACKET.
ADJUSTMENT, BUT IF YOU DO IT WILL REQUIRE THE
FOR SETTINGS. YOU SHOULD NOT HAVE TO DO ANY VERTICAL
THE SCREWS. REFER TO TYPE AND DISTRIBUTION CHART
POSITION. THEN SLIDE IT BACK DOWN AND TIGHTEN
1/4" AND SLIDE IT BACK OR FORTH TO THE DESIRED
OF THE SOCKET BRACKET. MOVE THE SOCKET UP ABOUT
LOOSEN THE TWO (DO NOT REMOVE) SCREWS ON EITHER SIDE
SOCKET ADJUSTMENT
AND CONNECT THEM TO THE PROPER TERMINALS ON THE
THEM SO THEY DO NOT INTERFERE WITH ANY COMPONENTS,
FEED THE SUPPLY WIRES THROUGH THE MAST ARM, DRESS
BOLTS TO 10 ft. lbs.
THE FRONT ONES. WHEN THE LUMINAIRE IS LEVEL, TORQUE
HIGH, LOOSEN THE TWO REAR FITTER BOLTS AND TIGHTEN
UNTIL THE LUMINAIRE IS LEVEL. IF THE FRONT END IS
TIGHTEN THE TWO REAR ONES. REPEAT THIS PROCEDURE
IS LOW, LOOSEN THE TWO FRONT FITTER BOLTS AND
MAST ARM UNTIL IT IS LEVEL. IF THE FRONT END
FROM SIDE TO SIDE, TWIST THE LUMINAIRE ON THE
THE LUMINAIRE. IF THE LUMINAIRE IS NOT LEVEL
PLACE A LEVEL ON THE AREA PROVIDED ON TOP OF
BOLTS FINGER TIGHT.
LUMINAIRE ON TO MAST ARM TO STOP AND TIGHTEN
MOUNTING LUMINAIRE ON A 2" MAST ARM. SLIDE
REMOVE CENTER OF BIRD SHIELD IF YOU ARE
1 1/4" MAST ARM & 1 1/4" FOR 2" MAST ARM.
LOOSEN FITTER CLAMP BOLTS. ABOUT 1/2" FOR
MOUNTING/LEVELING
LIFT OFF UPPER HOUSING.
LATCH. ROTATE LOWER HOUSING ABOUT 140í AND
OPEN LOWER HOUSING BY PULLING ON FRONT TRIGGER
REMOVE LOWER HOUSING
FOLD INSULATING BARRIER DOWN
AFTER CONNECTING WIRES
APPLY RTV BETWEEN WEATHER
GUARD AND REAR OF HOUSING
WARNING
DISCONNECT POWER BEFORE RELAMPING OR WIRING THE FIXTURE.
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL
AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION, CONSULT LOCAL CODE AUTHORITY
CAUTION
!
!