Flat lens model, Flat lens model refractor model refractor model, Maintenance and cleaning – American Electric Lighting 285 new User Manual
Page 2: Optional photocontrol
American Electric Lighting a division of Acuity Lighting Group, Inc. Conyers, GA
DRAWING NO. A66799 REV -
(BACK)
©2004 ACUITY LIGHTING GROUP, INC.
�
PART NUMBER 057-71-66799
FLAT LENS MODEL
FLAT LENS MODEL
REFRACTOR MODEL
REFRACTOR MODEL
The optical assembly should be cleaned with a mild detergent
The optical assembly should be cleaned with a mild detergent
and rinsed well with clean water to maintain the efficiency
and rinsed well with clean water to maintain the efficiency
of the luminaire. See the instruction under LAMP INSTALLATION
of the luminaire. See the instruction under LAMP INSTALLATION
AND SERVICE to open the bezel.
AND SERVICE to open the bezel.
To remove the refractor, push back on the spring steel retainers
To remove the refractor, push back on the spring steel retainers
to disengaged them from the refractor and then lift the refractor
to disengaged them from the refractor and then lift the refractor
out of the bezel. To replace it, orient the "street side" of the
out of the bezel. To replace it, orient the "street side" of the
refractor so it is adjacent to the latch, insert it into the bezel
refractor so it is adjacent to the latch, insert it into the bezel
To remove the lens, depress the two spring slide clips and remove
To remove the lens, depress the two spring slide clips and remove
lens. To replace, slide lens under rear retainer and push down.
lens. To replace, slide lens under rear retainer and push down.
The spring side clips will snap over glass and retain it.
The spring side clips will snap over glass and retain it.
To remove the lens, rotate clips riveted to side of bezel 180
To remove the lens, rotate clips riveted to side of bezel 180°°..
Then push back on the spring steel retainer located at the hinge
Then push back on the spring steel retainer located at the hinge
side of bezel, push lens up and slide out. To replace it, orient
side of bezel, push lens up and slide out. To replace it, orient
the lens so the masked side will be inside, and the flat portion
the lens so the masked side will be inside, and the flat portion
of masked lens will be next to latch side of bezel after it is
of masked lens will be next to latch side of bezel after it is
slid in place. Rotate side clip back in place.
slid in place. Rotate side clip back in place.
MAINTENANCE AND CLEANING
MAINTENANCE AND CLEANING
REFLECTOR (BOTH MODELS)
REFLECTOR (BOTH MODELS)
The reflector can be removed by loosening the
The reflector can be removed by loosening the
two captive screws, which hold it up inside of the
two captive screws, which hold it up inside of the
the housing. However, the socket electrical connector
the housing. However, the socket electrical connector
located inside of the ballast compartment should be
located inside of the ballast compartment should be
disconnected first. Reverse this procedure to replace
disconnected first. Reverse this procedure to replace
the reflector.
the reflector.
To remove the bezel, position it so that it is only
To remove the bezel, position it so that it is only
partially open and then disengage it from the hinge
partially open and then disengage it from the hinge
hooks.
hooks.
NOTE: In luminaire with the OPTIONAL HINGE KEEPER
NOTE: In luminaire with the OPTIONAL HINGE KEEPER
feature, the hinge keepers will have to be slid
feature, the hinge keepers will have to be slid
sideways to the left (facing to the rear). "Unlock"
sideways to the left (facing to the rear). "Unlock"
the hinges, to allow the hinges to be engaged or
the hinges, to allow the hinges to be engaged or
disengaged. After engaging the hinges, the hinge
disengaged. After engaging the hinges, the hinge
keepers should be slide over to the right (facing
keepers should be slide over to the right (facing
to the rear) to the "locked" position to assure
to the rear) to the "locked" position to assure
that the hinges will remain engaged.
that the hinges will remain engaged.
Loosen the receptacle clamping screw, rotate the
Loosen the receptacle clamping screw, rotate the
receptacle and twist it clockwise until it locks
receptacle and twist it clockwise until it locks
into position.
into position.
OPTIONAL PHOTOCONTROL
OPTIONAL PHOTOCONTROL
This fixture is not designed for use with S55SD-150 or S56SE-150 lamps.
This fixture is not designed for use with S55SD-150 or S56SE-150 lamps.
Use of these lamps can result in mechanical damage to the fixture.
Use of these lamps can result in mechanical damage to the fixture.
CAUTION
!