AZEK Deck EN - Manual (Page 2)

Page 2
AZEK Deck/Rim Joist Covers/Riser should be installed using the same good building principals used to
install wood or composite decking and in accordance with the local building codes and the installation
guidelines included below. AZEK Building Products Inc. accepts no liability or responsibility for the
improper installation of this product. AZEK Deck/Rim Joist Covers/Riser may not be suitable for every
application and it is the sole responsibility of the installer to be sure that AZEK Deck/Rim Joist Covers/
Riser is fit for the intended use. Since all installations are unique, it is also the installer’s responsibility to
determine specific requirements for each Deck application. AZEK Building Products recommends that all
applications be reviewed by a licensed architect, engineer or local building official before installation. If
you have any questions or need further assistance, please call AZEK Customer Service at 1-877-ASK-AZEK,
(877) 275-2935 or visit our website at www.azek.com.
Tools Required
AZEK Deck/Rim Joist Covers/Riser can be installed with a minimum number of readily available tools.
Many other tools are available that can be used for installation. All tools should be used per applicable
manufacturers’ instructions. Some of the basic tool requirements:
• Cordless Driver • Carpenter Square
• Chalk Line
• Spacing Tools
• Tape Measure • Miter Saw
• Jig Saw • Safety Glasses
Use the jigsaw to cut around obstructions such as posts. For best results a miter saw with a fine-toothed,
carbide-tipped finish trim blade (12”-60 tooth minimum) works well for cutting. For a power miter or
compound power miter saw a fine finish alternate top bevel blade is also recommended. When working
with AZEK products be sure to wear proper clothing and safety equipment. Safety glasses should be
used during the entire installation process. Do not use any cordless saws.
STOP! Read this section before you start!
Cantilevering
For best results, don’t cantilever over 1/2”.
Routing
AZEK Deck/Rim Joist Covers/Riser should not be
routed with the exception of the start/stop boards
in the XLM Collection (see page 6 step 8).
Color and Grain Patterns
Color variation is purely aesthetic and does not or
will not affect the performance of the product.
Note
AZEK Deck is NOT intended for use as columns,
support posts, beams, joist stringers, guard
railing or other primary load-bearing members.
AZEK must be supported by a code-compliant
substructure. While AZEK products are great
for deck re-planking (removing old deck surface
boards and installing AZEK on code-compliant
substructure), AZEK Deck Boards CANNOT be
installed on top of an existing deck.
AZEK Deck
AZEK does not recommend the use of rubber or
vinyl products (welcome mats, planters, etc.) on
deck boards. A reaction can occur that causes
discoloration of the decking under the rubber/vinyl
product. This is a common caution for vinyl decking
products. Do NOT nail AZEK Deck boards. Cutting
or drilling metal should not be done on AZEK Deck
boards as metal shavings may be come hot and
embed themselves into the deck boards. Always be
sure to check and cut the factory cut ends of boards
to ensure they are square.
Walking Surface
AZEK deck boards need to be installed embossed
side up.
Static Electricity
Static build-up is a natural occurring phenomenon
that can occur with many plastic products including
PVC Decking. It could occur with AZEK products
under the right environmental conditions.
For most current care and cleaning, technical information and more, visit www.azek.com.
Visit http://azek.com/technical-center/installations/deck.aspx to view AZEK installation videos.
Installation Guidelines
Failure to install AZEK Deck products in accordance with applicable building codes and this Installation
Guide may lead to personal injury, affect deck system performance and void the product warranty.