Beijer Electronics iX T10A EN - Manual (Page 2)

Parameter iX T10A
Active area of display,
W × H 211.2 × 158.4 mm
Operating temperature -10 °C – +60 °C
Storage temperature -20 °C – +70 °C
Relative humidity 5 - 85% non-condensed
Approvals and
certifications Information is available on the web site
www.beijerelectronics.com
(1) See section Chemical Resistance for more information.
(2) iX T10A panels with part number 630000301 use a rechargeable battery. All
other versions use a BR 2032 battery.
4 Chemical Resistance
4.1 Metal Casing
The frame and casing material is powder-coated aluminum. This powder paint
withstands exposure to the following chemicals without visible change:
Acetic acid 10% Phosphoric acid 4%
Citric acid 10% Phosphoric acid 10%
Diesel Sea water
Distilled water Sodium chloride 2%
Edible oil Sodium chloride 20%
Fuel oil Sulphuric acid 20%
Hydrogen peroxide 3% Tap water
The powder paint shows limited resistance to the following chemicals at room
temperature:
Butanol Nitric acid 3%
Hydrochloric acid 5% Nitric acid 10%
Isopropyl alcohol Phosphoric acid 43%
Na-hypochlorite 10% Turpentine
Note:
If exposure to any of the above chemicals is demanded, it is recommended to
first test the chemical in a hidden spot of the metal casing.
The powder paint shows little or no resistance to the following chemicals at room
temperature:
Acetic acid, conc. Methyl-ethyl ketone Toluene
Acetone Nitric acid 30% Trichlorethylene
Ammonia 5% Phenol Xylene
Ammonia, conc. Sodium hydroxide 5% 97 octane unleaded petrol
Ethyl acetate Sodium hydroxide 30% 98 octane leaded petrol
4.2 Touch Screen and Overlay
4.2.1 Autoflex EBA 180L
Autoflex EBA 180L covers the overlay surrounding the touch screen.
Solvent Resistance
Autoflex EBA 180L withstands exposure of more than 24 hours duration under
DIN 42 115 Part 2 to the following chemicals without visible change:
Acetonitrile Diesel Downey /
Lenor
(1)
Phosphoric acid (<30%)
Ajax / Vim in
solution Ethanol Potassium ferricyanide
Alkalicarbonate
solution
(1)
Glycerine Potassium hydroxide
(<30%)
Ammonia (<40%) (1) Glycol Pure Turpentine
Acetic acid (<50%) Gumption (1) SBP 60/95 (1)
Ariel powder in
solution
(1)
Hydrochloric acid
(<36%) Sulfuric acid (<10%)
Bleach (1) Linseed oil Tomato ketchup
Castor oil Methanol Trichloroacetic acid
(<50%)
Caustic soda
(<40%)
(1)
Nitric acid (<10%) White Spirit
Cutting oil Paraffin oil Windex (1)
Cyclohexanol Persil powder in
solution
(1)
Wisk
Diacetone alcohol Petroleum spirit (1) -
(1) Extremely faint glossing of the texture was noted.
Autoflex EBA 180L withstands DIN 42 115 Part 2 exposure of up to 1 hour
duration to glacial acetic acid without visible change.
Autoflex EBA 180L is not resistant to high pressure steam at over 100 °C or the
following chemicals:
Concentrated mineral acids Benzyl alcohol
Concentrated caustic solution Methylene chloride
4.2.2 Touch Screen Surface
The touch screen surface on the operator panel withstands exposure to the following
solvents without visible change:
Solvents Time
Acetone 10 minutes
Isopropanol 10 minutes
Toluene 5 hours
4.2.3 Autoflex EBA 180L
It is recommended to use the Autoflex EBA 180Ltouch display protection film, that
can be ordered from Beijer Electronics.
Solvent Resistance
Autoflex EBA 180L withstands exposure to the same chemicals as Autotex F157 or
F207 according to section
Autoflex EBA 180L .
Outdoor Use
In common with all polyester based films, Autoflex EBA 180L is not suitable for use
in conditions of long-term exposure to direct sunlight.
5 Operator Panel Drawings
5.1 Connectors
1 2 3 4
COM 3/4 LAN COM 1/2
Pos. Connector Description
1 Power supply +24 V DC (18-32 V DC)
2 COM 1/2 Communication Ports
3 LAN 1 × 10/100 Base-T (shielded RJ-45)
4 COM 3/4 Communication Ports
5.2 Communication Ports
Serial port, 9-pin female Serial port, 9-pin female
Pin
COM1 COM2 COM3 COM4
1 -
RS422 Tx+
RS485 Tx+/Rx+
-
RS422 Tx+
RS485 Tx+/Rx+
2 RS232 RxD - RS232 RxD -
3 RS232 TxD - RS232 TxD -
4 - RS422 Rx+ - RS422 Rx+
5 GND GND GND GND
Serial port, 9-pin female Serial port, 9-pin female
Pin
COM1 COM2 COM3 COM4
6 -
RS422 Tx-
RS485 Tx-/Rx-
-
RS422 Tx-
RS485 Tx-/Rx-
7 RS232 RTS - - RS422 RTS+
8 RS232 CTS - - RS422 RTS-
9 - RS422 Rx- - RS422 Rx-
Note:
In order to utilize two communication ports on the same physical port, the
Y-split cable CAB109 must be used.
Drawing for external cable CAB109 (drawing # Z7100-029E) is available on the
web site:
www.beijerelectronics.com
Note:
Only iX T10A panels with part number 630000301 are equipped with
terminated COM-ports.
5.3 iX T10A Outline
USB host SD memory
card slot
Expansion port
COM3 RS232 / COM4 RS422/RS485
COM1 RS232 / COM2 RS422/RS485
Ethernet
24 V DC
209 9 9
7
44
228
max. 8 mm
262
9
9
280
Note:
A Step CAD file is available on the web site
www.beijerelectronics.com
Order no: MAEN017F
Copyright © 2013-09 Beijer Electronics. All rights reserved.
The information in this document is subject to change without notice and is
provided as available at the time of printing. Beijer Electronics AB, including
all its group companies, reserves the right to change any information without
updating this publication. Beijer Electronics AB, including all its group
companies, assumes no responsibility for any errors that may appear in this
document. Read the entire installation manual prior to installing and using
this equipment. Only qualified personnel may install, operate or repair this
equipment. Beijer Electronics AB, including all its group companies, are
not responsible for modified, altered or renovated equipment. Because the
equipment has a wide range of applications, users must acquire the appropriate
knowledge to use the equipment properly in their specific applications. Persons
responsible for the application and the equipment must themselves ensure that
each application is in compliance with all relevant requirements, standards and
legislation in respect to configuration and safety. Only parts and accessories
manufactured according to specifications set by Beijer Electronics AB, including
all its group companies, may be used.
BEIJER ELECTRONICS AB, INCLUDING ALL ITS GROUP
COMPANIES, SHALL NOT BE LIABLE TO ANYONE FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE INSTALLATION, USE OR REPAIR
OF THIS EQUIPMENT, WHETHER ARISING IN TORT, CONTRACT,
OR OTHERWISE. BUYER'S SOLE REMEDY SHALL BE THE REPAIR,
REPLACEMENT, OR REFUND OF PURCHASE PRICE, AND THE
CHOICE OF THE APPLICABLE REMEDY SHALL BE AT THE SOLE
DISCRETION OF BEIJER ELECTRONICS AB, INCLUDING ALL ITS
GROUP COMPANIES.
Head office
Beijer Electronics AB
Box 426
201 24 Malmö, Sweden
www.beijerelectronics.com / +46 40 358600