Full Throttle Skidoo 007-1023 - Manual

B) Installation of Right-Side Throttle Adapter Plate (See Photo B)
1) Using a screwdriver or needle-nose pliers, remove the OEM (original) throttle pivot pin snap-ring from the
ORIGINAL throttle on the right side.
2) Remove the pivot pin and washers and put them in your toolbox (you won’t need them anymore).
3) Starting from the top, insert the long allen screw first through a washer, then into the throttle flipper, then into the
pivot pin hole on the throttle block housing.
4) Then put two washers on the long allen screw, followed by the stainless steel adapter plate with the bent tab end
toward you. The adapter plate tab should be pointed UP so that it fits into the space between the throttle flipper and
the throttle block housing.
5) Next, place 1 more washer on the long allen screw and secure with the nyloc nut. (If there is still too much
unthreaded space on the long allen screw use the extra washers in the kit to make up the difference.)
Revised July 2009
CAUTION: INSTALLATION IS ALWAYS AT YOUR OWN RISK.
Improper assembly of this device may result in serious injury or even death, not to mention catastrophic damage to your machine. Before beginning, you
must carefully read ALL INSTRUCTIONS, as well as attached DISCLAIMER INFORMATION. If you have any questions, no matter how silly, consult an
professional mechanic or call to speak with one of our Technical Advisors at (509) 927-7533. While installation is quite simple, it should ONLY be
performed by those possessing solid mechanical abilities.
IF YOU ARE NOT MECHANICALLY INCLINED WE RECOMMEND YOU SEEK OUT EITHER A PROFESSIONAL MECHANIC
OR YOUR DEALER TO INSTALL THE GOLDFINGER ON YOUR SNOWMOBILE!
TOOLS NEEDED
Other than the tools supplied with kit, you should only need: a pair of diagonal cutters (dikes) to trim excess cable, a pair of slip-joint pliers, and 1 tube
Blue Loctite.
PARTS LIST
A. GOLDFINGER lever and perch with safety pin installed (1)
B. Stainless steel cable (1)
C. Black cable housing (1)
D. 1” clear nylon spacer (1)
E. Allen wrenches (2, small and large)
F. Plastic zip-ties (4)
G. Flat washers (5)
H. Nyloc nut (1)
I. Barrel bolt (1)
J. Ferrule end (2)
K. Aluminum cable crimp cap (1)
L. Short allen screw (1)
M. Stainless steel adapter plate (1)
N. Long allen screw (1)
O. Rubber accordion boot (1)
(For Early Model SKIDOO SNOWMOBILES
with ROUND-SLIDE CARBS)
INSTALLATION INSTRUCTIONS
A) Installation of Left-Side Throttle Lever Perch (See Photo A)
On most models the throttle lever perch will fit over the left side handlebar grip with no modifications to the
grip. The goal for this section will be to position the throttle lever perch assembly as closely as possible to the
left side of the brake reservoir/switch switch housing on the left side of handlebars, with the lever hanging
straight down.
1) Using smallest (2.5mm) allen wrench supplied in kit, remove the 2 lever perch allen screws, then remove
the perch cap.
2) Position lever perch and cap over handlebar grip as closely as possible to the left side of the brake
reservoir/switch housing assembly on the left side of handlebars. The GOLDFINGER lever should hang in
approximately the 6:00 position, or 90 degrees separated from the brake lever. (Note: If you have wider
aftermarket bars and the lever perch will be installed directly over the handlebars instead of the grips, you can
use the nylon spacer provided in your kit.)
3) Thread allen screws back into perch housing, being careful not to cross-thread screws.
4) Once the lever perch fits snugly and the allen screws thread smoothly, tighten the screws to prevent the
perch from rotating loosely on the handlebar. CAUTION: In no case should your GOLDFINGER throttle lever be parallel or close to your brake lever!
A
B