Rugged Ridge Hardtop Insulation Kit, 4-Door, 07-10 Jeep Wrangler (JK) - Manual

Contents 2DR (12109.01)
(1) Front driver's side panel
(1) Front passenger's side panel
(1) Rear panel
(1) Bag - 4" Velcro Strips
Page 1 REV.3 8/24/11
Omix-Ada Inc.
460 Horizon Dr. Suite 400
Suwanee, Georgia 30024
12109.01 Two Door Acoustic Headliner - Hardtop
12109.02 Four Door Acoustic Headliner - Hardtop
Installation Instructions: 2007- 2010 JK Acoustic Hardtop Healiner (2dr - 4dr)
Step 4: Place 4" 3M Velcro strips in locations shown in supplied image. Proper placement of the Velcro strips is
needed for a secure fit. With 4" strips attached to headliner remove protective backing tape from strips
being very careful not to get dirt or grease on adhesive. With the help of a second person carefully place
liner into recess of the hard top panel. Press firmly against liner and hardtop working around the liner
making sure all strips have been pressed against top. DO NOT REMOVE headliner. Allow Velcro
adhesive to cure for 72 hours before removing or adjusting acoustic liners.
Step 1: Clean surface where acoustic liner is to be installed with isopropyl (rubbing) alcohol. Freedom top front
panels can be removed for cleaning and installation.
Step 2: Make sure surface is dry and clean. DO NOT proceed until surface is completely dry.
Step 3: The acoustic liners have been designed to fit the hardtop recesses. Hold liner up into each section of
the hardtop before applying Velcro strips to insure that the correct liner is being installed into the correct
location.
Step 7: Place 4" 3M Velcro strips in locations shown in supplied image. Proper placement of the Velcro strips is
needed for a secure fit. With 4" strips attached to headliner remove protective backing tape from strips
being very careful not to get dirt or grease on adhesive. With the help of a second person carefully place
liner into recess of the hard top panel starting at the sound bar. The liner has been designed to fit the
shape of the sound bar to allow installation without the removal of the hard top. Starting at the outer corners
of the recess work around hardtop pressing firmly against liner and top. Make sure all strips have been
pressed against top. DO NOT REMOVE head liner. Allow Velcro adhesive to cure for 72 hours before
removing or adjusting acoustic liners. .
Contents 4DR (12109.02)
(1) Front driver's side panel (1) Bag - 4" Velcro Strips
(1) Front passenger's side panel
(1) Middle panel
(1) Rear Panel
4 door and 2 door front driver's / passenger's side panel installation
Step 5: Make sure surface is dry and clean (see step #1).DO NOT proceed until surface is completely dry.
Step 6: Slide liner up and between the hardtop and sound bar. Note the correct orientation of the liner. It has been
shaped to match the sound bars profile. Confirm that the liner fits correctly before proceeding.
4 door center panel and 2 door rear panel installation
4 door rear panel installation
Step 9: Clean surface where acoustic liner is to be installed (see step #1). DO NOT proceed until surface is
completely dry. Position liner in rear recess to find correct orientation.
Step 10: Place 4" 3M Velcro strips in locations shown in supplied image. Proper placement of the Velcro strips is
needed for a secure fit. With 4" strips attached to headliner remove protective backing tape from strips
being very careful not to get dirt or grease on adhesive. With the help of a second person carefully place
liner into recess of the hard top panel. Starting at the outer corners of the recess work around hardtop
pressing firmly against liner and top. Make sure all strips have been pressed against top.
DO NOT REMOVE headliner. Allow Velcro adhesive to cure for 72 hours before removing or adjusting
acoustic liners..