Silverline Air Brush Kit 6pce - Manual (Page 2)

Introduction
Carefully read and understand this manual before using this
product. Keep these instructions with the product for future
reference. Ensure all persons who use and service this product
are acquainted with this manual.
General Safety Instructions
It is important to read and understand your instruction manual and
any label attached to the power tool. Learn its application, as well
as it's limitations and the potential hazards associated with this
power tool. Even when used as prescribed it is not possible to
eliminate all residual risk factors. Use with caution.
Keep guards in position
• Always keep guards in position, in good working order, correctly
adjusted and aligned. Never attempt to use a power tool without
any guard supplied with it.
Remove adjusting keys
• Always check to see that keys and adjusting wrenches are
removed from power tool before turning on.
Clean work area
• Accidents occur where benches and work areas are cluttered or
dirty, floors must be kept clear, avoid working where the floor is
slippery due to sawdust or wax.
Dangerous environment
• Do not use power tools in damp or wet conditions, or expose
them to rain. Provide adequate surrounding work space and
keep area well lit. Do not use power tools where there is a risk
of explosion or fire from combustible material, flammable
liquids, flammable gases or dust of an explosive nature. When
using power tools avoid contact with any earthed items such as
pipes, radiators, cookers, refrigerators, metal baths and taps.
Children & Pets
• Children and pets should always be kept at a safe distance
from your work. Make your workshop child-proof. Lock tools
away where children can't get access to them. Remove
batteries from cordless tools.
Don't use excess force.
• Your power tool will give you much better service if you do
not use excessive force when using it.
Use the correct power tool
• Don't force, or attempt to use a power tool for a purpose it was
not designed for. Do not use a small tool to do the job of a
heavy duty tool.
Wear correct clothing and footwear.
• Don't wear loose clothing, neckties or jewellery or other items
which may get caught in moving parts. Wear non-slip footwear,
cover or tie back long hair. Use safety footwear if necessary.
Protect your head
• Wear safety goggles at all times, every day glasses are not
sufficient for eye protection, as lenses are not impact resistant
and could shatter. Use an approved face or dust mask when
operation creates dust. Ensure dust extraction equipment is
functioning and correctly used. Hearing protection should be
used if the sound intensity level for the operator could exceed
85dB(A). Use a hard hat where there is a risk of falling objects
or striking your head on low level obstructions.
Protect yourself from vibration.
• Hand held power tools may produce vibration. Vibration can
cause disease. Gloves to keep the operator warm and dry and
therefore maintain good blood circulation in the fingers may
help.
Secure work
• Always secure work. Where practical use a clamp or vice, it
will allow you to use both hands to operate your power tool.
Keep your balance
• Don't over reach, keep proper footing at all times to ensure
correct balance.
Maintain your power tool
• Keep your power tool in good working order, keep tools
sharp and clean for best and safest performance. Ensure
ventilation holes are kept clean and unrestricted at all times.
Always disconnect
• Before changing tools, always ensure they are disconnected
from the power source.
Avoid accidental starting
• Make sure the switch is in the OFF position before plugging
in the mains lead.
Accessories
• The use of any attachment or accessory other than those
mentioned in this manual could result in damage or injury. The
use of improper accessories could be dangerous.
Never stand on your power tool
• Standing on your power tool or its stand could cause serious
injury if the tool is tipped or if the cutting tool is accidentally
contacted. Do not store materials above or near the tool so that
it is necessary to stand on the tool or its stand to reach them.
Switch off before connecting.
• Ensure the power tool is switched off before connecting to the
power source. If the power tool stops unexpectedly turn the
power switch to off.
Do not abuse the power cord.
• Be sure your cable/extension cable is properly wired and in
good condition. Always replace a damaged cable/extension
cable or have it repaired by a qualified person before using it.
Never yank or pull the cable to disconnect it from the power
socket. Never carry your power tool by it’s cable. Keep the
cable away from damp, heat, oil, solvents, and sharp edges.
Check for damaged or missing parts.
• Before each use check if any part of the power tool is damaged
or missing, check carefully that it will operate properly and
perform its intended function. Check alignment of moving parts
for binding. Any guard or other part that is damaged should be
correctly repaired or replaced. Do not use if the power switch
does not turn the power on and off. Check any other condition
that may affect the safety of the power tool. DO NOT USE IF
DEFECTIVE.
Direction of feed
• Feed work into a blade or cutter against the direction of rotation
of the blade or cutter only.
Don't leave the tool running unattended
• Always wait until your power tool has come to a complete stop
before leaving it and then disconnect from power source.
1. Nozzle
2. Finger Lever
3. Air Hose
4. 22cc Paint Bottle
SPECIFICATION
Nozzle
0.35mm
Capacity 22cc
Average Consumption 0.4-0.7CFM
Air Pressure Required 20-45PSI
ADDITIONAL SAFETY INSTRUCTIONS FOR AIR TOOLS
• Always wear safety goggles or safety glasses.
• Always wear ear protection.
• Always make sure that the machine is switched OFF before
connecting to the air supply.
• Disconnect any machine from the air supply before changing
blades or discs.
• Disconnect any machine from the air supply before performing
any servicing.
• Ensure you keep machines clean and lubricated. Lubrication is
essential to prevent corrosion of internal parts leading to
machine failure.
• Ensure that the machine is oiled daily to prevent corrosion.
• Never wear jewellery (not limited to but including. watches,
rings, bracelets or necklaces) or loose clothing when operating
air tools.
• Use lightweight coil hoses from the tool to the wall, or
compressor coupling.
• Do not overload the machine. Allowing the machine to work at
its optimum speed prolongs life and is more efficient.
• Do not increase air pressure above the recommended level,
excessive overload leads to wear of moving parts and possible
tool failure, it can also cause the machine casing to split.
Weight 0.7KG
Min Hose Size 5mm
• Always ensure the machine has fully stopped before putting it
down after use.
• Make sure that the work piece is firmly secured allowing the
operator to control the machine with both hands.
• Ensure that any blades or accessories are rated for use with
the machine.
• Always make sure that blades, discs or other accessories are
correctly secured and fastened before connecting the machine
to an air supply.
• Always fit a whip hose to the air tool.
• Use a straight hose only with spray guns. Do not use coil type
hoses.
• Do not aim the spray gun at people or animals.
• When spraying keep away from heat and naked flames.
• Never spray corrosive or flammable liquids eg. Petrol etc.
• Always wear protective equipment including, but not limited to
overalls, gloves, facemask etc.
• When spraying it is essential that you have a clean filtered air
supply.
• Spray in a well ventilated area or a specialist spray booth.
Product Familiarisation
Air Brush Kit
1
3
2
4