Aqua Bath C6530TD-FUS 2 - Manual (Page 2)

10/08
AQUA BATH COMPANY INC.921 Cherokee Ave.Nashville, TN 372071-800-232-2284Fax (615) 227-9446
 www.aquabath.com 
CARE SERIES
• Model
C6530TD-FUS 2”-L seat on left.
• Model C6530TD-FUS 2”-R seat on right.
• Bath units designed for hospitals, nursing homes, rehabilitation
centers, hotels, motels and residential applications.
• Meets ANSI A117.1, ADA Guidelines and other standards
for accessibility
• Acrylic one-piece molded construction simplifies installation.
• Inside dimensions: 60” W x 30” D x 78” H.
• Can be furnished complete with valve, hand held shower set,
curtain and hooks.
• Barrier-Free Shower System, U.S. Patent No.6,178,571 B1.
• 2” threshold for pit detail installation.
• Factory installed fold-up seat full depth of stall.
• 25¾” x 35” x 1½” two wall wrap grab bar.
• Vacuum-formed from .1875” one-piece sanitary grade acrylic.
• Manufacturing Tolerance Of (±1/4”) Due To The Nature
Of The Materials Used.
Roll-In Shower Stall
The shower enclosure shall be Aqua Bath model C6530TD-FUS 2” acrylic and be molded from a single sheet so as not to have
any joints or seams, shall meet ANSI Z124.2. Shall meet ADA guidelines and other standards for accessibility. Unit shall have a
backside flame spread of less than 30 (Class B). Shall be designed to be ADA COMPLIANT and NAHB LISTED.
The enclosure shall have inside dimensions of 60” W x 30” D x 78” H and outside dimensions of 65” W x 31” D x 84” H.
The approximate weight of the unit shall be 275lbs. The unit shall be formed with a patented recessed trench system so as to
direct water to the front drain. ADA states that the threshold must be flush with the finished floor. Because of the threshold
height, the unit must be installed in a pit to comply with ADA.
Standard Accessories:
1) One 25¾” x 35” x 1½” diameter two wall horizontal wrap grab bar fabricated from 18 gauge stainless steel with 1½” safety
statute clearance, mounted with stainless steel bolts and secured from the rear with 3” x 3” x 11 gauge metal mounting plates.
2) 28” "L" shaped phenolic fold-up seat. 3) 1” diameter, 18 gauge stainless steel curtain rod.
After grab bars, fold-up seat and curtain rod have been factory installed, they will be sealed from the backside making the unit
completely waterproof. 4) Ribbed bottom for slip resistance (standard).
Available Accessories:
1) Hand held shower set (includes 60” flex hose, swivel connector, brass nipple, lock nut, wall outlet and vacuum breaker).
2) 24” slide bar, 30” slide bar or two (2) wall brackets installed on valve wall for use with hand held shower set.
Note: The determination of the use of slide bar or wall brackets to be installed in the unit is based upon the valve package
chosen by the specifier for use in the unit. Aqua Bath recommends the use of a slide bar as an accessory in the unit rather
than the use of a glide bar / glide rail.
3) Pressure balance or thermostatic control valve. 4) Shower curtain - antibacterial, with hooks. 5) Seat belt.
6) Weighted shower curtain (patented), antibacterial, with hooks.
7) Dome light (factory drilled only, must be field installed and light shipped separately from unit).
8) ASTM F462 non-slip bottom. (*) When the ASTM F462 bottom is specified with the center drain location,
it will re-configure the trench drain system. A signed off approval is required for the bottom re-configuration.
Modifications: Received and / or approved by:
Name:______________________________
Company:___________________________
Title:_______________________________
Phone:______________________________
Date:_______________________________
Please check with your local city and
state for code compliancy. Aqua Bath's
advertised ADA compliant units are
based on our interpretation of the
Americans with Disabilities Act 1991
Guidelines. Field alterations or improper
installation could take the units out of
compliance. Aqua Bath accepts no
responsibility for final code compliance.
For additional information, call the
Aqua Bath Customer Service
Department At 1-800-232-2284