Aqua Bath C6530BF-OT-FUS 2 - Manual (Page 2)

For additional information, call the
Aqua Bath Customer Service
Department At 1-800-232-2284
Please check with your local city and
state for code compliancy. Aqua Bath's
advertised ADA compliant units are
based on our interpretation of the
Americans with Disabilities Act 1991
Guidelines. Field alterations or improper
installation could take the units out of
compliance. Aqua Bath accepts no
responsibility for final code compliance.
CARE SERIES - OPEN TOP UNIT
•
Model C6530BF-OT-FUS 2"-L valve on left.
• Model C6530BF-OT-FUS 2"-R valve on right.
• Bath units designed for hospitals, nursing homes, rehabilitation
centers, hotels, motels and residential applications.
• Shall accommodate a wheelchair or a shower chair.
• Meets ANSI A117.1, ADA Guidelines and other standards
for accessibility
• Acrylic one-piece molded construction simplifies installation.
• Inside dimensions: 60" W x 30" D x 74" H.
• Includes stainless steel grab bars with mounting plates.
• Can be furnished complete with valve, hand held shower set,
curtain and hooks.
• Barrier-Free Shower System, U.S. Patent No.6,178,571 B1.
• 2" threshold.
• 25¾" x 35" x 1½" wrap grab bar.
• Shower brackets.
• Factory installed fold-up seat full depth of stall.
OPEN TOP ROLL-IN SHOWER STALL
The shower enclosure shall be Aqua Bath model C6530BF-OT-FUS 2" acrylic and be molded from a single sheet so as not to
have any joints or seams, shall meet ANSI Z124.2. Shall meet ADA guidelines and other standards for accessibility. Unit shall
have a backside flame spread of less than 30 (Class B). Shall be designed to be ADA COMPLIANT and NAHB LISTED.
The enclosure shall have inside dimensions of 60" W x 30" D x 74" H and outside dimensions of 65" W x 31" D x 76" H.
The factory installed fold-up seat adds 3/4" to outside dimension width. A soap tray shall be molded in the back center 24" above
the shower floor. The unit shall be formed with a patented recessed trench system so as to direct water to the center drain. The
approximate weight of the unit shall be 275lbs. The unit, regardless of threshold height, requires a pit to be ADA compliant.
ADA states the threshold must be flush with the finished floor.
The enclosure shall be pre-drilled and equipped with the following factory installed accessories: 1) One 25¾" x 35" x 1½"
diameter, 2-side wrap, 18 gauge stainless steel grab bar with 1½" safety statute clearance, mounted with stainless steel bolts and
secured from the rear with 3" x 3" x 11 gauge metal mounting plates. 2) 28" "L" shaped phenolic fold-up seat.
3) Two wall brackets installed at 40" and 64" above the floor on back wall for hand held shower set. After grab bar and wall
brackets have been factory installed, they will be sealed from the backside making the unit completely waterproof.
4) Ribbed bottom for slip resistance (standard). 5) Self-caulking brass drain with stainless steel strainer (not installed).
AVAILABLE OPTIONS
1) Hand held shower set (includes 60" flex hose, swivel connector, brass nipple, lock nut, wall outlet and vacuum breaker).
2) 24" or 30" slide bar. 3) Pressure balance or thermostatic control valve. 4) Shower curtain - antibacterial, with hooks.
5) Weighted shower curtain (patented), antibacterial, with hooks. 6) Factory installed fold-up seat. 7) Seat belt.
8) Dial thermometer. 9) ASTM F462 non-slip bottom.
(*) When the ASTM F462 bottom is specified with the center drain location, it will re-configure the trench drain system.
A signed off approval is required for the bottom re-configuration.
Modifications: Received and / or approved by:
C6530BF-OT-FUS 2"
02/05
 AQUA BATH COMPANY INC.921 Cherokee Ave.Nashville, TN 372071-800-232-2284Fax (615) 227-9446
 www.aquabath.com 