ConTech Lighting CA16 - Manual

INSTALLATION INSTRUCTIONS
For Incandescent Stemlight Pendant Series:
CM12, CA12 and CA16
www.con-techlighting.com 1-847-559-5500 INCNSTMLT INST All specifications subject to change without notice.
1
Continued on page 2
Nipple
Mono-Point Canopy
Swivel Stem
Attachment
IMPORTANT SAFETY INSTRUCTIONS:
• Read all the instructions before installation. Save instructions for later use.
• Turn off power at fuse or circuit breaker box before installation or before doing any maintenance work.
• Wear rubber soled shoes and work on a sturdy wooden or non-conductive ladder.
• Product must be mounted in locations and at heights in a manner consistent with its intended use, and in compliance with National Electrical
Code and local building codes. For indoor use only.
• Do not exceed the nominal supply voltage or amperage ratings.
• Make sure all screws are properly tightened.
• Do not install any lampholder closer than 6" from any curtain or similar combustible material.
• Use only fixtures and fittings intended for use with Con-Tech Stemlight Pendant systems.
• Installing contrary to instructions may cause unsafe conditions.
• Warning: Risk of fire. Most dwellings built before 1985 have supply wire rated at 60°C. Consult a qualified electrician before installation.
• Warning: Risk of burns. Lamps are extremely hot when lit. Allow lamps to cool down in temperature before handling.
• To avoid hazards to children, account for all parts and properly dispose of all packing materials.
• Call the Technical Support department at Con-Tech Lighting with any installation questions: 847.559.5500.
INSTALLATION PROCEDURES
TB MOUNT: Flexible Cable Track Mount, Dry Location Listed
Ensure track system is properly mounted to the ceiling structure.
Follow fixture assembly instructions.
When the entire assembly is completed, install into the track, observing polarity.
SB MOUNT: Flexible Cable Mono-Point, Damp Location Listed
SS MOUNT: Rigid Stem Mono-Point, Damp Location Listed
Ensure 4" Round or 4" Square (with a Round-to-Square Junction Box Cover Plate) Junction Box is properly mounted to the ceiling structure.
The center-to-center mounting holes on the 4" Round Junction Box are 3-1/2"; the Round-to-Square Junction Box Cover are 2-3/4". Both use
8-32 x 1/2" screws. Loosen the (2) Philips screws that hold the mounting strap to the top round wiring compartment. Attach the mounting
strap to the junction box or junction box cover.
Follow fixture assembly instructions.
FIXTURE ASSEMBLY INSTRUCTIONS
The Bicycle Cable Connector with has (1) 2mm recessed Allen Screw for locking into
the nipple plus (2) 2mm recessed Allen Screws for locking into the bicycle cable. (1)
2mm Allen Wrench is supplied with each fixture.
The shade/hood assembly comes with 132" of socket lead wiring (Blue, Red, Green)
in a silicone sleeve.
Bicycle Cable: Determine length of Bicycle Cable required. If cutting is required,
loosen bicycle cable from connector. Slide the bicycle cable off the
wiring. Remove wire grommet. Cut bicycle cable with a hacksaw
using a fine tooth (32T) blade, BX Armor cable cutter or high speed
metal cutting blade. Remove any sharp edges. Re-insert internal wire
grommet. Slide bicycle cable over the wiring (socket wiring: Red,
Blue; plus Green ground). Note: The Bicycle Cable will only accept the
wires less the silicone sleeve. Re-insert the Bicycle Cable Connector.
Tighten all the Allen screws along the way to the maximum.
Rigid Stem: Determine the length of the stem with internal coupling required for your
job. A swivel stem attachment is included for sloped ceiling applications,
35º adjustment. Assemble the stems onto the shade/hood assembly one
at a time, carefully feeding the wiring through each section. After all the
stems are attached completely, insert the wiring into the bottom of the
canopy. Screw the stem(s) into the nipple. Tighten all the Allen screws
along the way to the maximum.
Allen Screw
Locks Onto
Nipple
Allen Screws
Lock Onto
Bicycle Cable
Bicycle Cable
Connector