Adder Technology DDC Ghost - Manual (Page 2)

DDC
Ghost
VGA
STAT
US
CLO NE COM PUT ER
MO NIT OR
Link the computer
to the BLUE
connector
B
Cloning EDID information
The DDC Ghost module contains a default set of EDID values which
may be used immediately with most monitors (see Standard EDID
Information). Alternatively, you can use a ‘donor’ monitor from which
you can clone new EDID information.
To clone EDID information
1 Link the BLACK connector of the DDC Ghost to the donor monitor
(diagram A).
2 Provide power for the DDC Ghost module in one of two ways, either:
• Link the BLUE connector of the DDC Ghost to a computer video
output for the duration of the cloning operation (diagram B), or
• Attach the optional 5VDC power adapter to the socket on the side
of the DDC Ghost module (diagram C).
3 Ensure that the donor monitor and the DDC Ghost module are
powered. The DDC Ghost red STATUS indicator should be on.
4 Using a narrow implement, press and hold the recessed button
labelled CLONE on the side of the module (diagram D). The STATUS
indicator will begin to flash slowly for five seconds. Release the
button while the indicator is still slowly flashing.
• If new EDID information is available, it will be copied to the DDC
Ghost module memory.
• If there is no EDID information to clone then the existing DDC
Ghost memory will be not altered.
• If there is an error during cloning then the DDC Ghost will be
automatically reset to its standard values.
5 When the operation is complete, the STATUS indicator will flash
rapidly five times. Disconnect the DDC Ghost module from the donor
monitor.
Resetting EDID information
If required, you can reinstate the standard EDID values (see Standard
EDID Information) into the DDC Ghost module memory.
To reset the EDID information
1 Ensure that the DDC Ghost is powered (either from the video output
of a host computer or an optional power adapter) and check that the
red STATUS indicator is on.
2 Using a narrow implement, press and hold the recessed button
labelled CLONE on the side of the module (diagram D). The red
STATUS indicator will flash slowly for five seconds and then will go
off for a further five seconds.
3 Release the button while the red STATUS indicator is off, following
the five slow flashes. The reset operation will take place and then
the red STATUS indicator will flash rapidly five times to indicate a
successful completion.
DD
C G
hos
t VG
A
STA TUS
CLO NE
COM
PUTER
MONIT
OR
Link the monitor
to the BLACK
connector
A
DDC
Gho
stV
GA
STA TUS
CLO NE
COMPUTER
MO NIT OR
If power is
unavailable from
the computer via the
BLUE connector, use
the optional 5VDC
power adapter
C
DD
C G
hos
t VG
A
STA TUS
CLO NE
COMPUTER
MONI
TOR
Press and hold the
recessed CLONE button.
Release it as follows:
To clone: While
indicator is slowly
flashing.
To reset: While
indicator is off
(immediately following
the slow flashes). D
Installing for normal operation
During normal operation, the DDC Ghost module supplies either
standardised or cloned EDID information to the computer instead of
the data from the connected monitor.
To install for normal operation
1 Link the BLACK connector of the DDC Ghost to the monitor
(diagram A).
2 Link the BLUE connector of the DDC Ghost to the computer
video output (diagram B)
Note: In operation, the red STATUS indicator should be on. If
it is not then power is not being correctly supplied from the
computer (pin 9 of the VGA connector). If this situation cannot
be resolved, attach the optional 5VDC power adapter to the
socket on the side of the DDC Ghost module (diagram C).
3 Switch on the computer and monitor in the normal manner.
Standard EDID information
The standard EDID information supplied within the DDC
Ghost module represents a standard analogue monitor
(with no manufacturer details) capable of resolutions up to
1600x1200@60Hz. Other presented information is as follows:
Manufacturer details
ID Manufacturer Name: NON
Product ID Code: 0000
Last 5 Digits of Serial Number: 00000
Week of Manufacture: 00
Year of Manufacture: 1990
Complete Serial Number: 0000000000
Video input definition
Analog Signal: 0.700, 0.300 (1.000 Vp-p)
Separate Syncs
Established timing I
720 X 400 @ 70Hz (IBM,VGA)
640 X 480 @ 60Hz (IBM,VGA)
640 X 480 @ 75Hz (VESA)
800 X 600 @ 60Hz (VESA)
Established timing II
800 X 600 @ 75Hz (VESA)
1024 X 768 @ 60Hz (VESA)
1024 X 768 @ 75Hz (VESA)
1280 X 1024 @ 75Hz (VESA)
Standard timing identification
1280 X 1024 @60Hz
1600 X 1200 @60Hz
1152 X 864 @75Hz
Note: The DDC
Ghost module has
the capacity to store
one standard EDID
data block plus one
extension block.