Alpine iDA-X305S - Manual (Page 35)

33
-EN
On / Off (Initial setting)
When the Media Xpander is on, you can adjust the Media Xpander level
(refer to page 33).
• The function is inoperable when Defeat is set to ON.
MX (Media Xpander) makes vocals or instruments sound distinct
regardless of the music source. The FM radio, CD, USB memory and
iPod/iPhone, will be able to reproduce the music clearly even in cars
with a lot of road noise.
Changing the source to which you want to apply Media
Xpander.
FM (Level 1 to 3, Non Effect):
The medium to high frequencies become clearer, and produces
well balanced sound at all frequencies.
CD (Level 1 to 3, Non Effect):
CD mode processes a large amount of data during playback.
MX takes advantage of this large data quantity to reproduce a
more clear, clean output.
MP3/WMA/AAC/iPod/BLUETOOTH Audio (Level 1 to 3, Non
Effect):
This corrects information that was lost at the time of
compression. This reproduces a well-balanced sound close to
the original.
DVD (Video CD)
(Level 1 to 2 (MOVIE), Non Effect):
The dialogue portion of a video is reproduced more clearly.
(Level 3 (MUSIC), Non Effect):
A DVD or Video CD contains a large quantity of data such as
music clip. MX uses this data to reproduce the sound
accurately.
AUX (Level 1 (MP3/WMA/AAC/iPod/BLUETOOTH Audio), Level 2
(MOVIE), Level 3 (MUSIC), Non Effect):
Choose the MX mode that corresponds to the media connected.
If two external devices are connected, a different MX mode for
each media can be selected.
• To cancel MX mode for all music sources, set MX to Off in step 4.
• Each music source, such as FM radio, CD, and MP3/WMA/AAC can
have its own MX setting.
• When the source changes from “MP3/WMA/AAC to CD-DA” or
“CD-DA to MP3/WMA/AAC”, MX-mode switching may delay
playback slightly.
• Setting to MX Off sets MX mode of each music source to Off.
• There is no MX mode for AM radio.
• The function is inoperable when Defeat is set to ON.
Flat/Pops/Rock/News/Jazz&Blues/Electric Dance/Hip Hop
&Rap/Easy Listening/Country/Classical/User 1~6*
10 typical equalizer settings are preset at the factory for a variety of
musical source material.
* By selecting User’s 1 to 6, you can recall the stored EQ Adjustment
value in “Storing and Recalling the Adjusted Contents” (page 36).
• The function is inoperable when Defeat is set to ON.
Subwoofer On (Initial setting) / Subwoofer Off
If an optional subwoofer is connected to the unit, make the following
setting.
When the subwoofer is on, you can adjust the subwoofer output level
(refer to page 21).
Sys 1 (Initial setting) / Sys 2
When the subwoofer is on, you can select either Sys 1 or Sys 2 for the
desired subwoofer effect.
Normal (Initial setting) / Reverse
The subwoofer output phase is toggled Subwoofer Normal (0°) or
Subwoofer Reverse (180°).
Stereo (Initial setting) / Mono
You can set the subwoofer output to stereo or monaural. Make sure to
set the correct output for your subwoofer type.
Maker’s (Initial setting) / User’s
Depending on the response characteristics of the speaker, care should be
taken when setting the response slope of the high range speaker to 0 dB/
oct in 3WAY mode (see “Adjusting the Crossover Settings” on page 35),
as speaker damage may result.
• You can set to Tweeter only when the system switch on the IMPRINT
audio processor (PXA-H100) is set to 3WAY.
Graphic / Parametric (Initial setting)
This setting gives you a choice of 5-band parametric, or 7-band graphic
equalizer.
• The function is inoperable when Defeat is set to ON.
Turning Media Xpander ON/OFF (MX)
Setting the MX Level
Equalizer Presets (Factory’s EQ)
Turning Subwoofer ON/OFF
Setting the Subwoofer System
Sys 1 : Subwoofer level changes according to the main
volume setting.
Sys 2 : Subwoofer level change is different from the main
volume setting. For example, even at low volume
settings, the subwoofer is still audible.
Setting the Subwoofer Phase
Setting the Subwoofer Channel
Stereo: Subwoofer stereo (L/R) output
Mono: Subwoofer monaural output
Setting the Response Slope for the High
Range Speaker (Tweeter)
Maker’s: As protection from possible speaker damage, 0 dB/
oct cannot be set for the response slope of the high
range speaker in 3WAY mode.
User’s: The 0 dB/oct setting is possible in 3WAY mode.
Setting EQ mode