Asus Motherboard NCL-DS - Manual (Page 78)

4 - 1 6 4 - 1 6 4 - 1 6 4 - 1 6 4 - 1 6 C h a p t e r 4 : B I O S s e t u p C h a p t e r 4 : B I O S s e t u p C h a p t e r 4 : B I O S s e t u p C h a p t e r 4 : B I O S s e t u p C h a p t e r 4 : B I O S s e t u p
Onboard IDE Operate Mode [Enhanced Mode] Onboard IDE Operate Mode [Enhanced Mode] Onboard IDE Operate Mode [Enhanced Mode] Onboard IDE Operate Mode [Enhanced Mode] Onboard IDE Operate Mode [Enhanced Mode]
Allows selection of the IDE operation mode depending on the installed
operating system (OS). Set to [Enhanced Mode] if you are using native OS,
e.g. Windows
® 2000/XP. Set to [Compatible Mode] if you are using legacy
OS, e.g. Windows ME/98/NT, MS-DOS.
Configuration options: [Compatible Mode] [Enhanced Mode]
IDE Configuration
Onboard IDE Operate Mode [Enhanced Mode]
Enhanced Mode Support On [S-ATA]
Configure S-ATA as RAID [No]
IDE Detect Time Out (Sec) [35]
When in AHCI/RAID
mode SATA
controller is
forced to Native
mode.
4.3.5 4.3.5 4.3.5 4.3.5 4.3.5 IDE Configuration IDE Configuration IDE Configuration IDE Configuration IDE Configuration
The items in this menu allow you to set or change the configurations for
the IDE devices installed in the system. Select an item then press <Enter>
if you wish to configure the item.
The items E n h a n c e d M o d e S u p p o r t O n E n h a n c e d M o d e S u p p o r t O n E n h a n c e d M o d e S u p p o r t O n E n h a n c e d M o d e S u p p o r t O n E n h a n c e d M o d e S u p p o r t O n and C o n f i g u r e S - A T A C o n f i g u r e S - A T A C o n f i g u r e S - A T A C o n f i g u r e S - A T A C o n f i g u r e S - A T A
a s R A I D a s R A I D a s R A I D a s R A I D a s R A I D appear only when you set the Onboard IDE Operate Mode to
[Enhanced Mode].
Enhanced Mode Support On [S-ATA]
Allows you to set Serial ATA, Parallel ATA, or both, to native mode.
Configuration options: [P-ATA+S-ATA] [S-ATA] [ P-ATA]
C o n f i g u r e S - A T A a s R A I D [ N o ] C o n f i g u r e S - A T A a s R A I D [ N o ] C o n f i g u r e S - A T A a s R A I D [ N o ] C o n f i g u r e S - A T A a s R A I D [ N o ] C o n f i g u r e S - A T A a s R A I D [ N o ]
Allows you to configure the Serial ATA devices as RAID sets.
Configuration options: [No] [Yes]
IDE Detect Time Out (Sec) [35] IDE Detect Time Out (Sec) [35] IDE Detect Time Out (Sec) [35] IDE Detect Time Out (Sec) [35] IDE Detect Time Out (Sec) [35]
Selects the time our value (in seconds) for detecting ATA/ATAPI devices.
Configuration options: [0] [5] [10] [15] [20] [25] [30] [35]