Audiovox Prestige 128-8121 User Manual
Page 4
128-8121
4 of 24
4
Action
System Response
Turn ignition on
No response
Press and release the valet switch 3 times
1 Chirp - LED 1 flash
Within 3 seconds, turn ignition Off, On, Off, On
Short chirp, then 2 long chirps
This Action Accesses Feature Bank 3 Remote Start Selectable Features
First
Press the valet switch one time
1 chirp = defrost output pulsed
Press transmitter Lock button to change
2 chirps = defrost output 10 Mins
o r
Second
Press and release the valet switch
2 chirps = RF start chirp on
Press transmitter Lock button to change
1 chirp = RF start chirp off
o r
Third
Press and release the valet switch
2 chirps = run time set for 10 mins
Press transmitter Lock button to change
3 chirps = run time set fro 15 mins
Press transmitter Lock button to change
4 chirps = run time set for 20 mins
Press transmitter Lock button to change
1 chirp = run time set for 5 mins
o r
Fourth
Press and release the valet switch
1 chirp = parking lights on steady w/RS active
Press transmitter Lock button to change
2 chirps = parking lights flashing w/RS active
o r
Fifth
Press and release the valet switch
2 chirps = tachometer input checking
Press transmitter Lock button to change
1 chirp = voltage sense input checking
o r
Sixth
Press and release the valet switch
1 chirp = greater than 0.5 V check before start
Press transmitter Lock button to change
2 chirps = less than 0.5 V check before start
o r
Seventh
Press and release the valet switch
2 chirps = ign 2 on during crank
Press transmitter Lock button to change
3 chirps = ign 2 same as accessory
Press transmitter Lock button to change
1 chirp = ign 2 off during crank
o r
Eighth
Press and release the valet switch
2 chirps = ign 3 on during crank
Press transmitter Lock button to change
3 chirps = ign 3 same as accessory
Press transmitter Lock button to change
4 chirps = Ign 3 same as starter
Press transmitter Lock button to change
1 chirp = ign 3 off during crank
o r
Ninth
Press and release the valet switch
1 chirp = diagnostics off
Press transmitter Lock button to change
2 chirps = diagnostics on
o r
Tenth
Press and release the valet switch
2 chirps = crank time 1.0 sec
Press transmitter Lock button to change
3 chirps = crank time 1.5 sec
Press transmitter Lock button to change
4 chirps = crank time 2.0 sec
Press transmitter Lock button to change
1 chirp = crank time 0.8 sec
o r
Eleventh
Press and release the valet switch
1 chirp = unit set for gasoline engine
Press transmitter Lock button to change
2 chirps = unit set for diesel engine 10 sec delay
Press transmitter Lock button to change
3 chirps = unit set for diesel engine 15 sec delay
Press transmitter Lock button to change
4 chirps = unit set for diesel engine 20 sec delay
o r
Twelfth
Press and release the valet switch
1 chirp = transponder output while R/S active
Press transmitter Lock button to change
2 chirps = transponder output during start only
Press transmitter Lock button to change
3 chirps = transponder output until ignition turned off
o r
Thirteenth
Press and release the valet switch
Non Functional On This Unit
o r
Fourteenth
Press and release the valet switch
1 chirp = crank averaging w/voltage input checking
Press transmitter Lock button to change
2 chirps = preset crank time w/voltage input check
Fifteenth
Non Functional On This Unit
o r
Sixteenth
Press and release the valet switch
1 chirp = turbo timer off
Press transmitter Lock button to change
2 chirps = turbo timer 3 mins
Press transmitter Lock button to change
3 chirps = turbo timer 5 mins
Press transmitter Lock button to change
4 chirps = turbo timer 10 mins
o r
Seventeenth
Press and release the valet switch
1 chirp = aux o/p Black/Blue single pulse
Press transmitter Lock button to change
2 chirps = aux o/p Black/Blue as alarm feature #1
Press and release the valet switch
or
turn the ignition off to:
Exit Programming Mode
Note : Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps or the
programming will be terminated.