Pioneer DDJ-WeGO-W - Manual (Page 11)

11 En
Basic
Operation
D D B A
B
C C
Loading tracks and playing them
( rA)
1 Turn the rotary selector while pressing the [SHIFT]
button to select a folder or item.
! When a folder or item with the [+] mark is selected and the rotary
selector is pressed while pressing the [SHIFT] button, that folder or
item is opened or closed.
2 Release the [SHIFT] button then turn the rotary
selector to select the track.
3 Press the [LOAD] button to load the selected track
onto the deck.
4 Press the [f] button to play the track.
! When this button is pressed again during playback, playback
pauses.
Using the mixer functions ( rB)
! Adjust the volume of the powered speakers, etc., connected to the
[MASTER OUT] terminals to an appropriate level. Note that if the
volume is set too high, the output sound could be very loud.
1 Operate the channel faders to adjust the audio level
output from the respective decks.
2 Operate the crossfader to switch the deck whose
sound is output from the speakers.
— Left edge: Sound is output from deck [A] or [C].
— Center: The sound of all the decks is mixed and output.
— Right edge: Sound is output from deck [B] or [D].
! The curve characteristics can be switched using the crossfader
curve setting button on the [MIXER] panel at the center of the com-
puter’s screen.
— [
]: Select this when you do not want to use the crossfader.
— [ ]: Set here for a curve that rises gradually.
— [ ]: Sets an abruptly rising curve.
3 Turn the [MASTER VOL] control to adjust the audio
level of the speakers.
Adjusting the sound quality
Turn the [EQ (HI, MID, LOW) ] controls on the respective
decks.
Monitoring sound with headphones
( rC)
1 Connect headphones to the [PHONES] terminal.
2 Press the [CUE ] button for the deck you want to
monitor.
3 Turn the [HEADPHONES MIX] control.
! Turn counterclockwise: The volume of the deck whose [CUE ] but-
ton is pressed increases relatively.
! Turn clockwise: The [MASTER OUT] volume increases relatively.
4 Turn the [HEADPHONES VOL] control.
! The sound of the deck whose [CUE ] button is pressed is output
from the headphones.
! When the [CUE ] button is pressed again, monitoring is canceled.
Mixing ( rB, D)
1 Operate the [TEMPO] slider to match the playing
speed on one deck to the playing speed on the other
deck.
— Move towards the + (front) side: The playing speed increases.
— Move towards the – (back) side: The playing speed decreases.
2 If the beats of the two decks are off, use the jog dial’s
pitch bend function to correct for this offset.
The playing speed can be adjusted by turning the outer part of the jog
dial during playback.
— Spin clockwise: The playing speed increases.
— Spin counterclockwise: The playing speed decreases.
— Stop spinning: Playback at the normal speed resumes.
! When the [SYNC (MASTER)] button is pressed, the playing speeds
and beats of the two decks are synchronized automatically. (The play-
ing speeds and beats are synchronized to those of the deck selected
as the master for synchronization.)
3 Operate the channel faders or crossfader to mix the
sound of the two decks and switch between them.
Inputting the sound of the
microphone
The sound of the microphone connected to the [MIC] terminal can be
mixed.
1 Connect the microphone to the [MIC] terminal.
2 Adjust the audio level input to the [MIC] terminal.
! Turn the [MIC VOL] control: The [MIC] terminal's input audio level is
adjusted.
! Only the volume of the microphone’s sound can be adjusted.
! The sound of the microphone is not output from the headphones.
Quitting the system
1 Quit VIRTUAL DJ LE.
2 Slide this unit’s [ON/OFF] switch to the [OFF] position.
3 Disconnect the USB cable from your computer.