Pioneer DEH-3200UB - Manual (Page 16)

FM step (FM tuning step)
Normally the FM tuning step employed by seek tuning
is 50 kHz. When AF or TA is on, the tuning step auto-
matically changes to 100 kHz. It may be preferable to
set the tuning step to 50 kHz when AF is on.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the FM tuning step.
100kHz (100 kHz) —50kHz (50 kHz)
3 Press M.C. to confirm the selection.
Auto PI (auto PI seek)
The unit can automatically search for a different sta-
tion with the same programming, even during preset
recall.
1 Press M.C. to turn Auto PI seek on or off.
AUX (auxiliary input)
Activate this setting when using auxiliary device con-
nected to this unit.
1 Press M.C. to turn AUX on or off.
USB PnP (plug and play)
This setting allows you to switch your source to USB/
USB-iPod automatically.
1 Press M.C. to turn the plug and play on or off.
ON
– When USB storage device/iPod is con-
nected, the source is automatically switched to
USB/USB-iPod. If you disconnect your USB sto-
rage device/iPod, this unit
’s source is turned off.
OFF – When USB storage device/iPod is con-
nected, the source is not switched to USB/USB-
iPod automatically. Please change the source to
USB/USB-iPod manually.
Brightness (display brightness setting)
1 Press M.C. to display the setting mode.
2 Turn M.C. to switch the brightness setting.
High (high) —Low (low)
3 Press M.C. to confirm the selection.
SW control (rear output and subwoofer setting)
Only for DEH-4200SD.
This unit
’s rear output (rear speaker leads output) can
be used for full-range speaker ( Full) or subwoofer
( SUBW) connection. If you switch the rear output set-
ting to SUBW, you can connect a rear speaker lead di-
rectly to a subwoofer without using an auxiliary amp.
1 Press M.C. to display the setting mode.
2 Turn M.C. to change the setting.
Rear SP: Full —SUBW
3 Press M.C. to confirm the selection.
Only for DEH-3200UB.
The rear speaker leads output (
Rear SP) and RCA out-
put ( Preout) of DEH-3200UB can be used for full-
range speaker ( Rear SP :Full/Preout :Rear) or sub-
woofer ( Rear SP :SUBW/Preout :SUBW) connection.
If you switch to Rear SP :SUBW, you can connect a
rear speaker lead directly to a subwoofer without
using an auxiliary amp.
Initially,
Rear SP is set for rear full-range speaker con-
nection ( Full). When Rear SP :Full is selected, you can
connect the RCA output to a subwoofer. In this case,
you can select whether to use the subwoofer control-
ler
’s (low pass filter, phase) built-in Preout :SUBW or
the auxiliary Preout :Rear.
1 Press M.C. to display the setting mode.
2 Press M.C. to cycle between as following:
Rear SP/Preout —Full (SUBW)/SUBW(Rear)
3 Turn M.C. to change the setting.
Rear SP: Full —SUBW
Preout: SUBW —Rear
! Even if you change this setting, there is no
output unless you turn the subwoofer output
on (refer to
SW setting 1 (subwoofer on/off
setting) on page 14).
! If you change this setting, subwoofer output
in the audio menu will return to the factory
settings.
4 Press M.C. to confirm the selection.
DEMO (demo display setting)
1 Press M.C. tp turn the demo display on or off.
Ever SCRL (scroll mode setting)
When Ever Scroll is set to ON, recorded text informa-
tion scrolls continuously in the display. Set to OFF if
you prefer the information to scroll just once.
1 Press M.C. to turn the ever scroll on or off.
Title (multi language)
This unit can display them even if they are embedded
in a European language or Russian.
Text information such as title name, artist name or
comment can be recorded on a compressed audio
disc.
! If the embedded language and the selected lan-
guage setting are not the same, text information
may not be displayed properly.
! Some characters may not be displayed properly.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the desired setting.
EURO (European) —RUSSIA (Russian)
3 Press M.C. to confirm the selection.
Operating this unit
En
16
Section
02