Pioneer DEH-P5900MP - Manual (Page 5)

Note:
• When this unit is installed in a vehicle without
ACC (accessory) position on the ignition switch,
red cable must be wired to the terminal that can
detect the operation of the ignition key.
Otherwise, battery drain may result.
• Use this unit in other than the following condi-
tions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative
grounding.
— Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
• To prevent short-circuit, overheating or malfunc-
tion, be sure to follow the directions below.
— Disconnect the negative terminal of the bat-
tery before installation.
— Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap adhe-
sive tape around them where they lie against
metal parts.
— Place all cables away from moving parts,
such as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors
with insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker’s nega-
tive cables.
• Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
external power amp’s system remote control or
the vehicle’s auto-antenna relay control terminal
(max. 300 mA, 12 V DC). If the vehicle is
equipped with a glass antenna, connect it to the
antenna booster power supply terminal.
• Never connect blue/white cable to external power
amp’s power terminal. Also, never connect it to
the power terminal of the auto antenna.
Otherwise, battery drain or malfunction may
result.
• IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.
• Black cable is ground. This cable and other prod-
uct’s ground cable (especially, high-current prod-
ucts such as power amp) must be wired separate-
ly. Otherwise, fire or malfunction may result if
they are accidentally detached.
• Cord function may differ according to the
product, even if cord color is the same. When
connecting this system, be sure to check all
manuals and connect cords correctly.
No ACC position ACC position
ON
S
T
A
R
T
O
FF
ACC ON
S
T
A
R
T
O
FF
+ +
+ +
≠ ≠
≠ ≠
1. This product
3. Antenna jack
4. Front output
5. Fuse (10 A)
25. System remote control
6. IP-BUS input (Blue)
7. IP-BUS cable
31. Right 30. Left
29. Front speaker
27. Blue/white (6*)
1*
3* 2*
4* 5*
2. Rear output or
subwoofer output
8. Multi-CD player
(sold separately)
11. Wired remote input
Hard-wired remote control
adaptor can be connected
(sold separately).
12. Note:
Depending on the kind of vehicle, the function of 3* and 5* may
be different. In this case, be sure to connect 2* to 5* and 4* to 3*.
13. Connect leads of the same
color to each other.
14. Cap (1*)
Do not remove cap if this
terminal is not in use.
15. Yellow (3*)
Back-up
(or accessory)
17. Red (5*)
Accessory
(or back-up)
16. Yellow (2*)
Connect to the constant
12 V supply terminal.
18. Red (4*)
Connect to terminal controlled
by ignition switch (12 V DC).
19. Black (chassis ground)
Connect to a clean, paint-free metal location.
20. ISO connector
Note:
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to
connect to both connectors.
21. Speaker leads
White: Front left +
White/black: Front left ≠
Gray:
Front right +
Gray/black: Front right ≠
Green:
Rear left + or subwoofer +
Green/black: Rear left ≠ or subwoofer ≠
Violet:
Rear right + or subwoofer +
Violet/black: Rear right ≠ or subwoofer ≠
22. Connect with RCA cables
(sold separately)
23. Power amp
(sold separately)
23. Power amp
(sold separately)
24. Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
26. Blue/white (7*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
28. Note:
The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and 7*
when Pin 5 is an antenna control type. In another
type of vehicle, never connect 6* and 7*.
32. Rear speaker or
subwoofer
29. Front speaker
32. Rear speaker or
subwoofer
33. Perform these connections when
using the optional amplifier.
35. Notes:
• Change the initial setting of this unit (refer to the Operation
Manual). The subwoofer output of this unit is monaural.
• When using a subwoofer of 70 W (2 Ω) , be sure to connect
with Violet and Violet/black leads of this unit. Do not connect
anything with Green and Green/black leads.
34. Yellow/black
If you use an equipment with Mute
function, wire this lead to the Audio Mute
lead on that equipment. If not, keep the
Audio Mute lead free of any connections.
9. AUX jack (3.5 ø)
Use a stereo mini plug cable
to connect with auxiliary
equipment.
10. Note:
Connecting the Units ENGLISH
Connection Diagram
1. This product
2. Rear output or subwoofer output
3. Antenna jack
4. Front output
5. Fuse (10 A)
6. IP-BUS input (Blue)
7. IP-BUS cable
8. Multi-CD player (sold separately)
9. AUX jack (3.5 ø)
10. Note:
Use a stereo mini plug cable to connect with
auxiliary equipment.
11. Wired remote input
Hard-wired remote control adaptor can be con-
nected (sold separately).
12. Note:
Depending on the kind of vehicle, the function of
3* and 5* may be different. In this case, be sure
to connect 2* to 5* and 4* to 3*.
13. Connect leads of the same color to each other.
14. Cap (1*)
Do not remove cap if this terminal is not in use.
15. Yellow (3*)
Back-up (or accessory)
16. Yellow (2*)
Connect to the constant 12 V supply terminal.
17. Red (5*)
Accessory (or back-up)
18. Red (4*)
Connect to terminal controlled by ignition swich
(12 V DC).
19. Black (chassis ground)
Connect to a clean, paint-free metal location.
20. ISO connector
Note:
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to connect
to both connectors.
21. Speaker leads
White: Front left +
White/black: Front left ≠
Gray:
Front right +
Gray/black: Front right ≠
Green: Rear left + or subwoofer +
Green/black: Rear left ≠ or subwoofer ≠
Violet:
Rear right + or subwoofer +
Violet/black: Rear right ≠ or subwoofer ≠
22. Connect with RCA cables (sold separately)
23. Power amp (sold separately)
24. Blue/white
Connect to system control terminal of the power
amp (max. 300 mA 12 V DC).
25. System remote control
26. Blue/white (7*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
27. Blue/white (6*)
28. Note:
The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and
7* when Pin 5 is an antenna control type. In
another type of vehicle, never connect 6* and 7*.
29. Front Speaker
30. Left
31. Right
32. Rear Speaker or subwoofer
33. Perform these connections when using the
optional amplifier.
34. Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead free
of any connections.
35. Notes:
•
Change the initial setting of this unit (refer to the
Operation Manual). The subwoofer output of this
unit is monaural.
• When using a subwoofer of 70 W (2
Ω), be sure
to connect with Violet and Violet/black leads of
this unit. Do not connect anything with Green
and Green/black leads.