Sharp R-21ATP - Manual (Page 6)

5
9 This oven is not intended to stack one on top of another.
NSTALLATION
I
WARNING:
Inspect the Oven:
Check the oven carefully for damage before and
regularly after installation.
• Make sure the door closes properly, that it is not
misaligned or warped.
• Check the hinges and door safety latches are
not broken or loose.
• Ensure the door seal and sealing surfaces are
not damaged.
• Inspect the oven interior and door for dents.
Caution Sheet:
Always keep the caution sheet (Special Instructions
and Warnings) close to the oven for your reference.
Important:
If any damage is apparent, do not operate the oven
in any way. Contact your dealer or an authorised
Service Technician appointed by SHARP.
1 Remove all packing materials. Remove the protec-
tive film (blue film) from the outer case cabinet (if cov-
ered). Do not remove the plastic film from the inside
of the oven window as this protects it from dirt.
2 Place oven on a secure, level surface, strong enough
to take the oven weight, plus the heaviest item likely
to be cooked in the oven.
Do not place this oven in a position which is not easily
accessible. To position the oven too high can be
dangerous because food can not be removed safely.
3 Ensure there is a minimum free space above the oven
of 15 cm.
4 Do not place the oven where heat, moisture or high
humidity are generated, (for example, near or above
a conventional oven) or near combustible materials
(for example, curtains). Do not block or obstruct air
vent openings, as obstructions may ignite due to the
emission of hot air.
5 Make sure the power supply cord is undamaged and
that it does not run under the oven or oven any hot or
sharp surfaces.
6 The socket must be readily accessible so that it can
be easily unplugged in an emergency.
7 Do not use the oven outdoors.
8 The unit may be secured to a countertop or stand. There
is a screw hole in the bottom of the unit. After the oven
is permanently placed, drill a hole through the counter
top for a 5 mm self-tapping screw. The hole should be
20 mm from the left side of the outer case cabinet and
180 mm back from the front edge of the cavity face plate.
Hole
180 mm
20 mm
BUILDING-IN-KIT
This oven is not designed to be built into a kitchen unit.
IMPORTANT! ELECTRICAL CONNECTION
• Do not allow water to come into contact with the power
supply cord or plug.
• Insert the plug properly into the socket as the plug may
otherwise overheat and catch fire.
• Do not connect other appliances to the same socket
using an adaptor plug as it may cause the wiring to
overheat and catch fire.
• If the plug or socket is loose or the power supply cord
is damaged, do not operate the oven, it must be
replaced by the special power cord. Contact your dealer
or a Service Technician appointed by SHARP.
A defective plug, power supply cord or socket may
overheat and catch fire during operation or cause an
electrical shock.
• When removing the plug from the socket always grip
the plug, never the mains lead as this may damage
the power supply cord and the connections inside the
plug.
• The product is fitted with a non-rewireable (moulded)
plug. Should it not be suitable for the socket outlet in
your kitchen, remove the plug and fit an appropriate
type, observing the wiring code given in "To replace
the mains plug" on page 33.
The fuse from a cut-off plug should be removed and the
plug disposed of in safe manner. Under no circumstances
should the cut-off plug be inserted into a socket outlet as
serious electrical shock may occur. The plug must not be
used without the fuse cover fitted.
When replacing the plug please ensure that you use a BSI
or ASTA approved plug to BS1363, this should be fitted
with a brown coloured 13 amp fuse approved by BSI or
ASTA to BS1362. If you have any doubt about electrical
connection seek the help of a qualified electrician.
WARNING
THIS APPLIANCE MUST BE EARTHED.
To wire an appropriate plug, follow the wiring code given
in "To replace the mains plug" on page 33.