Behringer U-CONTROL UMX61 - Manual (Page 5)

5
U-CONTROL UMX49/UMX61
1. INTRODUCTION
1. INTRODUCTION
Thank you for showing your confidence in BEHRINGER
products by purchasing the UMX. The UMX is an extremely flexible
master keyboard with a controller unit that can be used for a
wide array of applications. Whether you need independent control
of computer rack synthesizers, general MIDI sound modules or
effects devices, or want to use the UMX for conveniently
operating sequencing software or computer plug-ins – the UMX
offers you tremendous ease of use and allows you to realize
your ideas intuitively.

The following user’s manual is intended to
familiarize you with the unit’s control elements, so
that you can master all the functions. After having
thoroughly read the user’s manual, store it at a safe
place for future reference.
1.1 Before you get started
1.1.1 Shipment
The U-CONTROL was carefully packed at the assembly plant
to assure secure transport. Should the condition of the cardboard
box suggest that damage may have taken place, please inspect
the unit immediately and look for physical indications of damage.

Damaged equipment should NEVER be sent directly
to us. Please inform the dealer from whom you
acquired the unit immediately as well as the
transportation company from which you took
delivery of the unit. Otherwise, all claims for
replacement/repair may be rendered invalid.

To assure optimal protection of your UMX during
transport, we recommend utilizing a carrying case.

Please always use the original packaging to avoid
damage due to storage or shipping.

Never let unsupervised children play with the
B-CONTROL or with its packaging.

Please dispose of all packaging materials in an
environmentally-friendly fashion.
1.1.2 Initial operation and power supply
Please make sure that the unit is provided with sufficient
ventilation, and never place the UMX on top of an amplifier or in
the vicinity of a heater to avoid the risk of overheating.
The power supply can be realized in different ways depending
on the main application area: For the installation of the UMX in a
studio environment, it is possible to connect the device directly
to a free USB port of the computer using the USB cable provided
(see fig. 1.1).
In case it is not possible to establish the power supply over
USB (e.g. because of an overload of the host computer due to
several USB devices connected), it is also possible to operate
the UMX with three 1.5-Volt batteries (type “AA”, see fig. 1.2).
U-CONTROL UMX
USB Cable (included)
Figure 1.1: Power supply via USB
Figure 1.2: The battery compartment on the bottom side of
the UMX
Open the battery compartment by pressing the shutter clamp
carefully in the direction of the battery compartment, while pulling
the cover of the compartment upwards.
Please note the following points when inserting the batteries:
V The +symbol of the batteries must coincide with the
+symbol of the compartment! Incorrect polarity will damage
the electronics!
V Do not mix old and new batteries! When you change the
batteries, always change all 3 batteries at the same time.
V Do not use damaged batteries. The UMX could be damaged
due to the leakage of chemicals.
V If you do not use the unit for an extended period of time,
please remove the batteries from the compartment. Here
again, the batteries could leak and damage the device.
After inserting the batteries, please close the battery
compartment and make sure the shutter clamp snaps into place
again.
If you do neither want to connect the power supply over USB
nor operate the unit with batteries, there is yet another possibility
to connect the UMX over an external power pack. Best suited
here is the BEHRINGER POWERSUPPLY PSU-SB. If you use a
different power supply, please observe the correct operational
data (9 V DC; 100 mA) and correct polarity of the connector
plug; you will find information about this above the DC input on
the rear of the unit. Reverse polarity can damage the electronics.
1.1.3 Online registration
Please, do remember to register your new BEHRINGER
equipment right after your purchase by visiting
www.behringer.com (alternatively www.behringer.de) and
kindly read the terms and conditions of our warranty carefully.
DATA-MANFULL_UMX49_ENG_Rev_A.pmd 12.01.2006, 20:36 5