Liebherr CBPesf 4033 Comfort BioFresh - Manual (Page 7)

u Screw the turn hinge Fig. 6 (25) firmly into place on the new
hinge side, possibly using a cordless screwdriver (with
4 Nm).
u Re-insert the stopper Fig. 6 (21) into the other hole.
u Re-insert the bearing pin Fig. 6 (22) together with washer
and foot. In so doing, pay attention that the locating lug
points backwards
4.3.5 Transferring the handles
On both the upper and lower door:
u Transfer the spring clamp
Fig. 7 (31) : Depress the
latch nose and pull the
spring clamp off over it.
u Slide the spring clamp
into place on the new
hinge side until it clicks
into place.
Fig. 7
Fig. 8
u Lift the stopper Fig. 8 (30) out of the door bearing bush and
transfer it.
u Detach door handle Fig. 8 (32) , stopper Fig. 8 (33) and pres-
sure plates Fig. 8 (34) and transfer to the opposite side.
u When fitting the pressure plates on the opposite side, make
sure they snap properly into place*
4.3.6 Fitting the lower door
u Place the lower door from above onto the lower bearing pin
Fig. 6 (22) .
u Close the door.
u Place the plastic cap Fig. 5 (10) back onto the middle turn
hinge Fig. 5 (13) .
u Place the middle bearing pin Fig. 5 (11) in the lower door, on
the new hinge side, through the middle turn hinge
Fig. 5 (13) .
4.3.7 Fitting the upper door
u Place the upper door on the middle bearing pin Fig. 5 (11) .
u Insert the upper turn hinge Fig. 4 (3) in the door on the new
hinge side.
u Screw the upper turn hinge firmly into place (with 4 Nm)
(2x Torx® 25) Fig. 4 (4) . Possibly make preliminary holes
with a bradawl or use a cordless screwdriver.
u Apply the cover Fig. 4 (1) and cover Fig. 4 (2) to the oppo-
site side from the outside and snap them into place.
4.3.8 Aligning the doors
u If necessary, align the doors to the appliance housing by
way of the two oblong holes in the bottom turn hinge
Fig. 6 (25) and middle turn hinge Fig. 5 (13) . To do so,
unscrew the middle screw in the bottom turn hinge
Fig. 6 (25) .
WARNING
Risk of injury due to the door dropping out!
If the bearing parts are not screwed into place firmly enough,
the door may drop out. This may lead to severe injuries. What
is more, the door may not close and therefore the appliance
may fail to cool properly.
u Screw the turn hinges firmly into place with 4 Nm.
u Check all of the screws and retighten if necessary.
4.4 Insertion into a row of kitchen units
Fig. 9
(1) Stack cabinet (3) Kitchen cabinet
(2) Appliance (4) Wall
x For appliances supplied with wall spacers, the measurement
increases by 35 mm (see 4.2) .
The appliance can be inserted into a row of kitchen units. To
match the appliance Fig. 9 (2) to the height of the row of units,
a suitable stack cabinet Fig. 9 (1) can be fitted above the appli-
ance.
When installing with kitchen units (max. depth 580 mm), the
appliance can be positioned directly next to the kitchen cabinet
Fig. 9 (3) . The appliance will project by 34 mm x at the sides and
50 mm x in the centre of the appliance in relation to the kitchen
cabinet front.
Ventilation requirements:
- At the back of the stack cabinet there has to be a ventilation
duct of at least 50 mm depth throughout the width of the
stack cabinet.
- The ventilation space under the ceiling has to be at least
300 cm 2 .
- the larger the ventilation space, the more energy-saving the
appliance is in operation.
If the appliance is installed with the hinges next to a wall
Fig. 9 (4) , the distance between appliance and wall has to be at
least 40 mm. This corresponds to the projection of the handle
when the door is open.
Putting into operation
* Depending on model and options 7