BOB OMS09B - Manual (Page 5)

backward tip-over more likely.
.
Adding weight to the seat back pocket (max weight 2 lbs. / 1 kg.).
.
Elevating the front wheel. Be careful when going up curbs, steps or other obstacles.
.
Pushing down on handlebar.
.
Jogging and or running. Always jog or run with the seat in the fully upright position.
.
Hanging items from handlebar. Items should not be hung from handlebar when seat
is in fully reclined position.
.
Using the stroller on uneven terrain and inclines.
.
To help prevent backward tip over, always hold handlebar.
To raise the seat to the fully upright position, fasten side release buckles and pull the
reclining strap loops. (Fig. 21 & 22).
For additional head clearance in fully upright and partially reclined positions:
Fold panel at top of seat down against seat back and attach Velcro.
Next, pull back on strap at top center of seat. Holding tension on strap, fold down and
connect Velcro on seat back. This strap tension will keep the top of seat (padded panel)
perpendicular to the seat back. (Fig. 21)
WARNING: Always jog with the stroller seat in the fully upright position. Jogging
with the seat fully reclined may result in a loss of stability and injury.
12. SHOCK ABSORBERS:
The suspension system features two shock positions to provide a comfortable ride for
kids of different weights. The two positions are shown in Fig. 2. Position 1 is intended
for occupant up to 40 lbs. (18 kg; total weight of occupant and cargo), while position 2
is intended for occupant from 40 to 70 lbs. (18 to 32 kg) total. The stroller features a
metal shock bracket with a sliding track and spring loaded shock pin that automatically
locks in place when it aligns with either of the two shock positions. Shock position
adjustments should be made with the stroller unloaded. The shocks will lock into position
1 when unfolding the stroller. To use the stiffer shock position, move the shock from
position 1 to position 2 by depressing the shock release button (Fig. 2) with one hand.
With the other hand, lift slightly and pull the shock backward. When the shock pin is
properly aligned in position 2, the pin will “snap” into place. Repeat this process for the
second shock. To move the shock from position 2 to position 1, reverse the above
process for both shocks.
13. WRIST SAFETY STRAP:
The wrist safety strap is designed to help prevent the stroller from rolling away should
you lose your grip on the stroller. When using the stroller make sure the strap is securely
looped over your wrist.
WARNING: Always use Wrist Safety Strap. Failure to use the Wrist Safetly Strap
can result in loss of control, injury and death.
14. FOLDING:
Remove child from stroller. Remove the contents of the Low Boy cargo pouch, seat
back and seat pockets. Press both the right and left handlebar release levers (Fig. 3),
and fold the handlebar forward as shown in Fig. 23. Locate the frame release handle
(red foam) underneath the seat (Fig. 24) and pull upwards sharply. This will allow the
lower frame to fold together, as shown in Fig. 25. The folded stroller can be made even
more compact by removing the front and rear wheels. To remove the front wheel, open
the brake quick release (Fig. 10), open front wheel quick release, then pull the wheel
forward (see section 6). Note that it is often easier to open the brake quick release
before you fold the handlebar. The rear wheels are removed by releasing the parking
brake (see section 8), and then opening the rear wheel quick release (Fig. 4), and pulling
each wheel directly to the side.
The Wrist Safety Strap can be used to keep the stroller in the folded position for transport
and storage. With the stroller folded, loop the end of the wrist safety strap around the
handlebar and back to the cross tube and fix the Velcro surfaces together (Fig. 26).
15. TIRE PRESSURE:
WARNING: Check tire pressure before every use.
Keep all tires inflated to 30 p.s.i.
16. STROLLER CARE & MAINTENANCE:
The fabric is 100% polyester with a stain resistant treatment that makes cleanup easy.
Use a sponge with a solution of mild soap and lukewarm water (maximum temperature
of 100 deg. F / 38 deg. C). Rinse thoroughly with clean water to remove soap then air
dry. Do not use detergent.
Regular maintenance should include: Verifying tire pressure, verifying that all screws
and fasteners are tight, checking for any tears or excessive wear in the fabric seating
which could lead to an accident, and wiping parts clean with a rag. To reduce the
possibility of squeaks, periodically apply a small amount of lubricant (Triflow, 3-in-one,
or light sewing machine oil) to the pivot axles and interior faces of the pivot brackets,
Shoulder
Strap
Crotch
Strap
Buckle
Fig 18 Place straps over shoulders
and secure to buckle.
Fig. 20 Connect sternum strap
Sternum
Strap
OMS01A P5
Fig. 19 Securely adjust shoulder straps
Shoulder
Strap
Auxiliary
Harness
Anchor
Fig. 21 Seat in fully upright position
Seat Reclining
Ladder Lock
Buckles
Additional head clearance:
Fold top panel,
connecting
Velcro
pieces.
Next,
Pull strap
and fasten
Velcro
Side Release
Buckles
(Fastened)
Fig. 22 Seat in fully reclined position
Reclining
Strap
Loops
Side
Release
Buckles
(Unfastened)