Belshaw Brothers BARO-1G - Manual (Page 2)

BELSHAW BROTHERS, INC. • Belshaw-Adamatic Bakery Group • 814 44th St NW, Suite 103, Auburn WA 98001
Phone: 206-322-5474 | 800-578-2547 Fax: 206-322-5474 • [email protected] • www.belshaw.com
©11/2007 Product specifications may be changed without notice. Always obtain current spec sheet at time of purchase.
27.50
V
VENT
Connection
Ø 8.00
Dimensions BARO-1G
Overall width 55” (1397 mm)
Overall height 104.5” (2654 mm)
Overall depth (inc. hood) 88.2” (2240 mm)
Depth at floor (not inc. hood) 51” (1295 mm)
Net weight 2500 lbs (1537 kg)
Shipping weight 2900 lbs (1318 kg)
Crate size 113”L x 62”W x 64” H
Crate volume 259 cu. ft.
Freight class 70
Electrical BARO-1G
120V-60-1 E-1 connection 12 A 1.5 kW
208V-60-3 E-2 connection 6 A 1.2 kW
240V-60-3 E-2 connection 5 A 1.2 kW
480V-60-3 E-2 connection 3 A 1.2 kW
Gas
BTU/hr 175,000
Connection 3/4” NPT
BARO-1G: Single Rack Oven, Gas
INSTALLATION REQUIREMENTS
Requires on-site installation •
Ships KD. When disassembled, can fit through 36” •
opening
Consult factory for shipment fully assembled
•
Two electrical connections •
For Controls/Lift and rotate (E1 on diagram): 1/2” EMT, •
120 VAC 1-Phase
For circulation blower (E2 on diagram): 1-1/4” EMT,
•
208-240V or 480V 3-Phase
112” Floor to ceiling height required for tip-up
•
Non-combustible floor supported by non-combustible •
structure
Zero clearance required from combustible surfaces on
•
side and back
GAS SUPPLy
3/4”NPT 175,000 BTU/hr •
Specify Natural Gas or Liquid Propane •
VENTILATION
8” Round vent collar (consult local codes for installation •
requirements)
530 CFM Roof vent (not included)
•
WATER SUPPLy & DRAINAGE
Supply: 1/2” NPT (9 GPM@40 psi) •
Drain: 3/4” NPT (210°F, 1 GPM) vented •
Line to be dropped from ceiling •
Connection will be located 100” above finished floor, 5.5” •
from the left side of the oven, 6” from the rear of the
oven
Oven comes pre-installed with water pressure regulator,
•
water pressure gauge, water solenoid and shut-off valve
Your local water conditions may damage your appliance.
•
Failure to properly treat water may result in damage and
may void your warranty. Ensure that your water supply
meets these minimum water quality specifications:
Alkalinity: 22 ppm –
Aluminum: 17 ppm –
Calcium: 3.3 ppm –
Free chlorine residual: 0.6 ppm –
Magnesium: 0.65 ppm –
PH range: 8.5 s.u. –
Sodium: 8.5 ppm –
Total Hardness: 11.9 ppm –
Consult your local water treatment company for proper •
water filtration system.
[Plan View]
104.88
55.00
99.75
51.00
84.20
86.00
5.50
5.81
1.50
44.00
D
W
DRAIN Connection
WATER Connection
[Front View] [Side View]
E1 E2
G
GAS & ELEC.
Connections
75.50