Binatone 3401 - Manual (Page 2)

page 2 GETTING READY FOR USE USING THE ANSWERING MACHINE page 3
1
2
3
4 Switch on power at the mains socket
Plug the mains power lead and the
telephone line cord into the back of the
unit as shown
Plug the telephone line cable directly
into the socket or into the two-way
adapter (see note above)
Plug the mains adapter into a
230 V AC, 50 Hz mains socket, with the
switch on the socket set to OFF
Conditions for use
You can connect the Celestia 400 to a public exchange line in
the UK. It is not suitable for connection to a PBX.
The ringer equivalence numbers (RENs) of all instruments
connected to an exchange line must not add up to more than 4.
The
has a REN of 1; most other phones and fax
machines have a REN of 1 unless marked otherwise.
Celestia 400
Installation
SAFETY WARNING
Do not install the
Celestia 400 where it
might get wet
The Celestia 400 should be installed where the
mains power cable will reach a 230V AC, 50 Hz
switched socket. NEVER try to lengthen the
mains power cable.
You can either wall mount the unit, using the
template supplied, or stand it on a flat surface.
If you leave the unit free-standing, you can fit
the support stand as shown, for the best
position, or in the front slot.
You need to have a telephone connected to your line as well as
your Celestia 400. If you wish to connect both units to the same
telephone line socket, use a two-way adapter (‘splitter’) widely
available from retailers.
Alternatively, you can connect the phone and the
Celestia 400 to different extension sockets.
MAINS
SLIDE INTO PLACE
The Celestia 400 must be used with mains
adapter, part no. XX002104D, supplied with
the unit. Using any other adapter will result in
non-compliance with EN41003, and will
invalidate any approval given to this apparatus.
TELEPHONE
LINE
Recording your outgoing message
09:35 13-10 02/05 AM MSG
00-32 -5
OGM REC 1
2
3
Press and hold until you hear a ‘beep’
Speak clearly into the microphone
Press the PLAY/PAUSE/STOP button when
you have finished speaking
Your outgoing message (OGM) can be between 3 and 60
seconds long. The display shows the recording time as you
speak. Do not pause for more than 10 seconds.
The machine will ‘beep’ then play back your OGM.
To check your OGM at
any time
• Press
To set the time and date, and the number of rings before the Celestia 400
will answer a call, refer to SETTINGS on pages 6 to 8..
NOTE: if you disconnect the Celestia 400 from mains
power, your time and date settings will be lost. However,
stored messages and Caller ID records will be retained. NOTE: if you lift the handset of any phone connected to the
same line as the Celestia 400, the machine will stop what it’s
doing and free the line for you to speak to the caller.
pause
stop
Recording a memo
Incoming calls
Switching the machine on and off
1
2
3
Press and hold until you hear a ‘beep’
Speak clearly into the microphone
Press the PLAY/PAUSE/STOP button when you have
finished speaking
Your memo will be stored as a new message.
w
w Press once —
Press again to switch the machine off
the machine says: ‘Answer on’ and the light comes on
memo
09:35 13-10 02/05 AM MSG
00-32 -5
MSG REC
11:05 13-10 02/05
11:05 13-10 02/05
AM
AM
MSG
MSG
02083448870
01-03
OGM
OGM
PLY
PLY UNAVAILABLE
This shows the duration of recording
The caller’s ID (phone number)
When the OGM is playing to the
caller, this appears
If the caller’s ID is unavailable (e.g. on
an international call) '
' is
shown; if the caller has withheld their
ID by dialling 1470, ‘
’ is shown.
UNAVAILABLE
WITHHELD
When a call comes in, the caller’s ID is shown on the display
(if you subscribe to the Caller ID service or equivalent).
To answer an incoming call
w
Press while the phone is ringing
Press while the OGM is playing or while the caller
is speaking
You can converse with the caller in hands-free mode.
Remember to speak clearly into the microphone
You can intercept a call which the machine has answered.
The machine stops recording the caller’s message, and
you can converse with the caller.
To intercept a call
w
16
16
CALL #
CALL # Do not clean any part of your Celestia
400 with solvent chemicals, abrasives or
spray cleaners which might get inside the
case and cause damage not covered by
the guarantee. When necessary, clean it
with a damp cloth.
Keep your Celestia 400 away from hot,
humid conditions or strong sunlight.
(If you prefer to have the unit
standing upright, slide the
support stand into the lower
slot, rather than as shown.)