Gradall 534B-9 Parts Manual User Manual
Page 185
OPTIONAL EQUIPMENT
(9104-5129) Steer Axle Advantage Kit
FOR SERVICE ONLY
Original Issue 3-96
Revised 1-12-99
Item
Part No.
Qty.
Description Of Part
31
9104-1450
AR
SHIM (.0478 thick, see note #3)
32
9104-1451
AR
SHIM (.106 thick, see note #3)
33
2
DRIVE HUB (use existing hubs )
34
9112-0004
1
R.H. STEERING KNUCKLE
35
8867-1008
2
LUBE FITTING, STRAIGHT, 1/4-28
36
8850-1006
2
HEX NUT, 3/8-16
37
8855-1011
6
LOCKWASHER, 3/8
38
8320-1144
2
HEX HD CAPSCREW, 3/8-16X5-3/4,
GR5
39
9108-1695
2
STEERING CYLINDER PIVOT PIN
(axle end)
40
8871-1280
2
HEX SOCKET PIPE PLUG, 1/8
41
9104-1598
AR
SHIM (see note #2)
42
2
STEERING CYLINDER ASSY (see page
13-23 for details)
43
9108-1523
1
L.H. TUBE SUPPORT
9108-1522
1
R.H. TUBE SUPPORT
44
8820-1035
4
HEX HD CAPSCREW, 3/8-16X1, GR5
45
8821-1121
2
SOCKET HD CAPSCREW,
1/2-13X6-1/2, GR8
46
9112-0003
1
L.H. STEERING KNUCKLE
47
9104-3247
2
SELF-ALIGNING BUSHING
48
8867-1001
2
LUBE FITTING, STRAIGHT, 1/8
49
9104-1731
16
SPACER
50
12
HARDENED WASHER, 3/4 (use
existing hardware)
51
12
HEX HD CAPSCREW, 3/4-10X2 (use
existing hardware)
52
9116-6063
1
TIE ROD (includes item 47)
53
8852-1208
2
HEX LOCKNUT, 1/2
54
9104-3222
2
12 PT. SCREW, 3/4-10X2, GR8
(lubricate & torque to 270-290 ft. lbs.)
(see note #4)
55
9104-3494
2
12PT. SCREW, 5/8-1X2-1/4, GR8
(torque to 200 ft. lbs.) (see note #4)
56
9020-1918
AR
SHIM (10 gauge thick, see note #2)
57
8855-1153
2
LOCKWASHER, 5/8
58
8821-2321
2
SLOT HD CAPSCREW,
5/8-11X3-3/4,GR8
59
2460-1570
2
LIP SEAL
60
9112-3031
2
BUSHING
61
9104-1489
2
BUSHING
62
8821-2321
2
SOCKET HD CAPSCREW,
5/8-11X3-3/4, GR8
63
8850-1110
2
HEAVY HEX JAM NUT, 5/8-11
Item
Part No.
Qty.
Description Of Part
9104-5129
Ref
STEER AXLE ADVANTAGE KIT
(includes all items except 33, 50 & 51)
9103-5240
1
STEERING KNUCKLE KIT (includes
items 2,4, 7 thru 14, 16 thru 22,
28 thru 32, 45, 53, 57 & 58 - one kit does
both sides)
9104-5152
Ref
STEERING CYLINDER PIN KIT
(includes one each of items 1, 2, 3, 12 &
21 thru 24 - one kit needed for each side)
1
8852-1312
2
HEX LOCKNUT, 3/4-10 (torque to
160-175 ft.lbs.)
2
9108-1415
2
DIRT SHIELD
3
9104-1481
2
STEERING CYLINDER PIN (knuckle
end)
4
9112-1239
2
BUSHING
5
9104-1439
2
TIE ROD PIN
6
8852-1306
2
LOCKNUT, 3/8-16
7
9112-1240
4
BUSHING
8
9112-3030
4
BACK-UP RING
9
8859-1032
4
O-RING
10
9112-3027
2
BUSHING (lower)
11
9112-3029
2
O-RING
12
8859-1104
4
O-RING
13
9112-1091
2
THRUST BUSHING
14
9104-1733
AR
SHIM
15
9104-6126
1
REAR AXLE WELDMENT
(includes items 10, 17, 60 & 61)
16
8692-1268
2
LIP SEAL
17
9112-3028
2
BUSHING (upper)
18
9108-1693
2
UPPER KING PIN
19
8858-1323
4
RETAINING RING
20
8867-1022
4
LUBE FITTING, 30 DEGREES, 1/8
21
9104-1732
AR
SPACER
9104-1438
AR
SPACER
22
8859-1019
2
O-RING
23
9104-1459
2
WASHER
24
8850-1416
2
HEX JAM NUT,1-14 (torque to
225-250 ft. lbs.)
25
8320-1140
2
HEX HD CAPSCREW, 3/8-16X2-3/4,
GR8
26
9103-3444
2
STREET ELBOW
27
9103-3445
2
LUBE FITTING
28
9114-1424
2
LOWER KING PIN
29
9104-1596
AR
SHIM (20 gauge thick, see note #3)
30
9104-1449
AR
SHIM (.060 thick, see note #3)
NOTE #1: CUSTOMER TO USE EXISTING WHEEL HUBS & HARDWARE, DRIVE MOTORS, DRIVE MOTOR
TUBE ASSEMBLIES, AND DRAIN LINE HOSES OR ORDER SEPARATELY IF REPLACEMENT IS REQUIRED.
NOTE #2: CYLINDER BASE END MUST BE FREE TO ROTATE. SHIM STEER CYLINDER BASE END AS
REQUIRED TO MAINTAIN A TOTAL MAX. GAP OF 1/16".
NOTE #3: SHIM BOTTOM KNUCKLES AS REQUIRED TO MAINTAIN NO MORE THAN
1/32" MOVEMENT. SHIM TOP KNUCKLES AS REQUIRED TO MAINTAIN NO MORE THAN 1/16" GAP. MUST
HAVE A MINIMUM OF ONE SHIM.
NOTE #4: ITEM 55 TO BE USED WITH FAIRFIELD HUBS ONLY.
13-22
PCN 971053, 971316, 980730 - JH
* Revised illistration and parts list, also added note #4.