Steele Products SP-PB101 - Manual (Page 3)

Guidelines for using extension cords
Make sure your extension cord is in good condition. When using an extension cord, be sure to use
one heavy enough to carry the current your product will draw. An undersized cord will cause a drop
in line voltage resulting in loss of power and overheating. The table below shows the correct size to
be used according to cord length and nameplate ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier the cord.
Minimum Gauge for Extension Cords (AWG)
(when using 120 V only)
Be sure your extension cord is properly wired and in good condition. Always replace a damaged
extension cord or have it repaired by a qualified person before using it.
Protect your extension cords from sharp objects, excessive heat and damp or wet areas.
Use a separate electrical circuit for your tools. This circuit must not be less than a #12 wire and
should be protected with a 15 Atime-delayed fuse. Before connecting the motor to the power line,
make sure the switch is in the OFF position and the electric current is rated the same as the current
stamped on the motor nameplate. Running at a lower voltage will damage the motor.
WARNING: This table saw is for indoor use only. Do not expose to rain or use in damp
locations.
WARNING: This tool must be grounded while in use to protect the operator from
electricshock.
Total Length of Cord in feet (meters) Ampere Rating
More Than Not More Than 25 (7.6) 50 (15) 100 (30.4) 150 (45.7)
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not Recommended
Electrical information (continued)
8
A Sliding miter gauge
B Blade guard
C Blade
D Table insert
E Rip fence
F Table G Blade elevation/tilting control
wheel
H Base
I Overload reset switch
J ON/OFF switch with safety key
K Blade bevel scale
L Blade bevel lock knob
M Anti-kickback pawl
N Splitter bracket
O Sawdust port
P Splitter
Q Leg stand
N
O
Q
P
M
G
I
J
K
L
A
B
C
D
E
F
H
Know your table saw
9
Unpacking (Fig. 1)
Carefully unpack the table saw and all its parts, and compare against the list below. Do not discard
the carton or any packaging until the miter saw is completely assembled.
4
G
J
A
B
D
I
P
O
H
C
E
F
L
K
N
M
A Table saw assembly
B Miter gauge
C Rip fence and handle
D Blade elevation wheel handle
E Blade guard assembly
F Allen wrench (2) G Blade wrenches
H Table insert
I Dado table insert
J Push stick
K Long top plates (2)
L Short top plates (2)
M Long support plates (2)
N Short support plates (2)
O Legs (4)
P Rubber feet (4)
Q Hardware kit (not shown)
Fig. 1
Assembly and adjustments
10
Assembly
Assembling the leg stand (Fig. 2)
Note: Use the screws (1), washers (2) , and lock nuts (3)
supplied in the hardware kit to attach the pieces of
the leg stand together. Do not tighten the hardware
completely until the leg stand is assembled.
1.Attach the short top plates (4) to the legs (6).
2.Attach the short support plates (7) to the legs (6).
3.Place the long top plates (5) over the short top plates
(4). Attach the long top plates (5) to the legs (6).
4.Attach the long support plates (8) to the legs (6).
5.Tap the four rubber feet (9) onto the bottom of
the legs (6).
Mounting the table saw to the leg stand (Fig.3)
Note: Mount the table saw to the leg stand using the
hardware supplied in the hardware kit.
1.Place the table saw onto the assembled leg stand so
that the four mounting holes (1) in the base of the
saw are over the four mounting slots in the two long
top plates (2).
2.Secure the table saw to the leg stand using the four
internal screws (3) washers (4), and lock nuts (5)
supplied in the hardware kit.
IMPORTANT! When mounting the table saw to the leg
stand, DO NOT overtighten the mounting hardware.
7
8
4
1
2
3
5
6
9
6
Fig. 2
1
2
3
4
5
Fig. 3
WARNING: To avoid injury from an accidental start, make sure the power switch is in the
OFF position and the plug is not connected to the power source outlet.
Assembly and adjustments (continued)
11