Jammin Pro StudioMix 10 - Manual (Page 8)

The circuitry of the British EQs is based on the technology used in the bast-known top-of-the-line consoles
and providing a warm sound without any unwanted side effects. The result are extremely musical equalizes
which, unlike simple equalizers, cause no side effects such as phase shifting or bandwidth limitation, even
with extreme gain settings of +15 dB.
All mono input channels include a 3-band equalizer. All bands provide boost or cut of up to 15 dB. In the
central position, the equalizer is inactive.
The upper (HI) and the lower band (LO) are shelving filters that increase or decrease all frequencies above
or below their cut-off frequency. The cut-off frequencies of the upper and lower band are 12 kHz and 80 Hz
respectively. The mid band (602/802/1002/1202) is configured as a peak filter with a center frequency of
2.5kHz
In addition, the mono channels are equipped with a steep LOW CUT filter
designed to eliminate unwanted low-frequenty signal components. These can be noise created by band-held
microphones, subsonic noise or plosive sounds created by highly sensitive microphones. (slope at 18 dB/oct., -3 dB at 75 Hz)
LOW CUT
EQ
please remember that you can only use either the microphone or the line input of a
channel at any one time. You can never use both simultaneously!
TRIM
Use the TRIM control to adjust the input gain. This control should always be turned fully counterclock
-wise whenever you connect or disconnect a signal source to one of the inputs.
5
FX sends enable you to feed signals via a variable control from one or more channels and sum these signals
to bus. The bus appears at the console’s FX send output and can be fed from there to an external effects device.
The
return from the effects unit is then brought back into the console on the aux return connectors or normal
channel inputs. Each FX send is mono and features up to +15 dB gain.
FX
The scale has 2 different value range: the first value range (+10 to +60 dB) refers to the MIC input and
shows the amplification for the signals fed in there.
The second value range (+10 to +60 dB) refers to the line input and shows its sensitivity. The settings
for equipment with standard line-level signals (-10dB or +4dBu) look like this: While the TRIM control is
turned all the way down, connect your equipment. Set the TRIM control is turned to the external devices
standard output level. If that unit that an output signal level display, it should show 0 dB during signal
peaks. For +4 dBu, turn up TRIM sightly. for -10 dBV a bit more. Tweaking is done using the CLIP LED.
Each mono input channel offers a balanced microphone input via the XLR connector and also
features switchable +48 V phantom power supply for condenser microphones. The StudioMix preamps
provide undistorted and noised-free gain as is typically known only from costly outboard preamps.
Please mute your play back system before you active the phantom power supply to prevent
switch-on thumps being directed to your loudspeakers. Please also note the instructions in
chapter 2.4“Main section”.
MIC
Each mono input also features a balanced line input on a connector. Unbalanced devices
(mono jacks) can also be connected to these inputs.
1/4
LINE IN
14
3 4 1 2
+10 -40 +10 +60
TRIM dB/dBu
BAL OR UNBAL
LINE IN
MIC
+10 -40 +10 +60
TRIM dB/dBu
BAL OR UNBAL
LINE IN
MIC
MAIN OUT L R L R CTRL ROOM OUT
LINE IN 5/6
L
R
MONO
BAL OR UNBAL
LINE IN 7/8 MONO
BAL OR UNBAL
LINE IN9/10 LINE IN 11/12 SEND FX
PHONES
0
- +15 8
L R
0
-15 +15 0
-15 +15 0
-15 +15
EQ
PAN
HIGH
12 KHz
MID
2.5 KHz
LOW
80 Hz
FX
CLIP
0
- +15 8
3 LEVEL
0
- +15 8
L R
0
-15 +15 0
-15 +15 0
-15 +15
EQ
PAN
HIGH
12 KHz
MID
2.5 KHz
LOW
80 Hz
FX
CLIP
0
- +15 8
4 LEVEL
0
- +15 8
L R
BAL
CLIP
0
- +15 8
5/6 LEVEL
0
- +15 8
L R
BAL
CLIP
0
- +15 8
7/8 LEVEL
0
- +15 8
L R
BAL
CLIP
0
- +15 8
9/10 LEVEL
0
- +15 8
L R
BAL
CLIP
0
- +15 8
11/12 LEVEL
+4
-10 +4
-10 +4
-10 +4
-10
L
R
CD/TAPE
IN OUT
0
- +15 8
MAIN MIX
10
0
10
15
20
25
30
40
60
8
MONO
BAL OR UNBAL
L
R
L
R
+10 -40 +10 +60
TRIM dB/dBu
BAL OR UNBAL
LINE IN
MIC
+10 -40 +10 +60
TRIM dB/dBu
BAL OR UNBAL
LINE IN
MIC
0
- +15 8
L R
0
-15 +15 0
-15 +15 0
-15 +15
EQ
PAN
HIGH
12 KHz
MID
2.5 KHz
LOW
80 Hz
FX
CLIP
0
- +15 8
1 LEVEL
0
- +15 8
L R
0
-15 +15 0
-15 +15 0
-15 +15
EQ
PAN
HIGH
12 KHz
MID
2.5 KHz
LOW
80 Hz
FX
CLIP
0
- +15 8
2 LEVEL
MONO
BAL OR UNBAL
L
R
FX FX FX FX
+48 V POWER
0
- +15 8 0
- +15 8
FX SENDS
L R
20
0
6
CLIP
PROGRAM (PUSH)
REVERB 00-39
ER/DLY 40-59
MOD 60-73 PITCH 74-79
MULTI 80-99
LOW CUT 75Hz 18 dB/Oct
LOW CUT 75Hz 18 dB/Oct
LOW CUT 75Hz 18 dB/Oct
LOW CUT 75Hz 18 dB/Oct
TAPE TO MIX
TAPE TO CTRL FX TO CTRL
PHONES
PHANTOM
1 2
3
1 2
3
1 2
3
1 2
3
-3
-6
-10
-15
-20
CLP 24-BIT DUAL ENGINE DSP
24-BIT A/D & D/A CONVERTER
88
TAPE
+6. . 66
MIDI sound module
Headphone
microphone
Active Speaker
CD player
Guitar
keyboard
Fig. 3.2: Live application of the StudioMix console
MD recorder
3.2 Live s ound