Defi Link VSD Concept - Manual (Page 13)

Engine speed Fuel press. Oil press.
■When the Defi-Link Display VSD CONCEPT is used WITHOUT a connection to the Defi-Link System
■When the Defi-Link Display VSD CONCEPT is used WITH a connection to the Defi-Link System When the Defi-Link Display VSD CONCEPT is used WITH a connection to the Defi-Link System
①Real Mode
NOTE: If "MPH, NOTE: If "MPH, ° F, PSI" is selected in the F, PSI" is selected in the
setting of units, data other than setting of units, data other than
the engine speed is not displayed.
the engine speed is not displayed.
NOTE: If "MPH, NOTE: If "MPH, ° F, PSI" is selected in the F, PSI" is selected in the
setting of units, data other than setting of units, data other than
the engine speed is not displayed.
the engine speed is not displayed.
Note)When displaying the speed minimum value, the unit(km/h or MPH) blinks and the
minimum value recorded in Rec Mode is displayed.
The actual data on current speed, engine speed, oil pressure, fuel pressure, oil temperature, water temperature, and
exhaust temperature is displayed in this mode. Each time the SELECT/BAR SELECT button is pressed, the displays
of the digital and bar section will change in the following order. Data without sensors connected cannot be selected.
②Peak Mode
NOTE: When connected to the Defi-Link System, the PEAK button of the D.C.Unit is unavailable. NOTE: When connected to the Defi-Link System, the PEAK button of the D.C.Unit is unavailable.
NOTE: When connected to the Defi-Link System, the PEAK button of the D.C.Unit is unavailable. NOTE: When connected to the Defi-Link System, the PEAK button of the D.C.Unit is unavailable.
※For operations ① through ⑨ shown below, refer to the Operation Manual for Defi-Link Control Unit II(or Defi-
Link Control Unit.
By pressing the PEAK button of Defi-Link Control Unit II(or Defi-Link Control Unit) during Real Mode, Peak
values are displayed. Displayed data will be changed by pressing SELECT/BAR SELECT button. Pressing the
PEAK button again during Peak Mode will return to Real Mode.
Digital Display
Section
Digital Display
Section
Bar Display
Section
Speed Oil temp. Oil press. Fuel press. Exhaust temp. Water temp.
Engine speed Fuel press. Oil press. Bar Display
Section
When the engine speed exceeds the warning value set as the tachometer warning1 in the setting of
tachometer warning, the green LED lights up. When it exceeds the tachometer warning2, the green and red
LEDs blink. The tachometer warning2 cannot be set in the setting of tachometer warning.
③Peak Reset Mode
When the UP button of the Defi-Link Control Unit II is pressed in Peak Mode(or when
the PEAK button of the Defi-Link Control Unit is pressed and held for more than two
seconds in any of Real Mode, Peak Mode or Warning Mode), the peak values will be
reset.
I)If the auto warning mode is turned ON in the setting of auto warning
NOTE: Even if REC button is pressed in vehicle's stopped condition, the vehicle speed data cannot be
recorded and Rec Mode will turn to Play Mode.
II)If the auto warning mode is turned OFF in the setting of auto warning
④Special Display Mode
Speed Maximum Speed Minimum Engine speed
Oil temp. Oil press. Fuel press. Exhaust temp.
Water temp.
If Special Display Mode is turned on in the setting of special display and speed is
0km/h or 0MPH for more than 10 seconds in Real Mode, special display will start. In
this mode, the engine speed is displayed digitally. When speed is more than 0km/h or
0MPH or when any button of D.C.Unit is pressed, the display will return to Real Mode.
NOTE: Once pause, fast-forward or rewind is performed with Defi-Link Control Unit II(or Defi-Link Control Unit), the
recorded speed data cannot be played back. To play back the speed data, Play Mode needs to be started
over again. Operation needs to be performed in vehicle's stopped condition. If the PLAY button is pressed
in vehicle's running condition, speed data will not be played back but Play Mode will turn to Rec Mode.
NOTE: The pulse free setting needs to be done again if units are changed.
NOTE: If the Defi-Link Display VSD CONCEPT is linked with the Defi-Link System, the setting of Defi-
Link Control Unit II(or Defi-Link Control Unit) is prioritized.
NOTE: This function operates when the Defi-Link Display VSD CONCEPT is linked with the Defi-Link
System and the temperature sensor is connected.
NOTE: This function operates when the Defi-Link Display VSD CONCEPT is linked with the Defi-Link
System and the temperature sensor is connected.
NOTE: If the Defi-Link Display VSD CONCEPT is linked with the Defi-Link System, the tachometer
warning2 cannot be set. The setting value of the tachometer warning of Defi-Link Control Unit
II(or Defi-Link Control Unit) is applied as a tachometer warning2. Please set up the tachometer
warning of Defi-Link Control Unit II(or Defi-Link Control Unit) higher than the tachometer
warning1 value. If the value is set lower than the warning1, the warning1 will be invalid.
NOTE: If the Defi-Link Display VSD CONCEPT is linked with the Defi-Link System, the warning buzzer
of Defi-Link Control Unit II cannot be absorbed.
NOTE: This function operates when the Defi-Link Display VSD CONCEPT is linked with the Defi-Link
System.
When the auto dimmer mode is on, the brightness of the display is adjusted automatically. Press
ENTER to Select one from three stages of brightness in the auto dimmer mode during the real mode or
the peak mode. When the manual dimmer mode is on, the brightness of the display can be set
manually at 5 stages in the real mode or the peak mode.