CARR 210874 Rota Light Bar - Manual

4XDOLW\ DQG 6W\OH WKDW (QGXUHV
Follow the diagram and the written
directions carefully for a proper, safe
installation.
Should you encounter an unusual,
unforeseen problem, contact our
Technical Help Line
7:00 AM – 3:00 PM Pacific Time
(951) 719-1068
Visit our web-site at
www.CARR.com
Carr Pattern Co., Inc.
WARNING!
THIS CARR LIGHT BAR IS DESIGNED TO HANDLE A TOTAL WEIGHT
OF FOUR (4) LBS. ANY ADDITIONAL WEIGHT
BEYOND THIS CAPACITY, MAY RESULT IN SERIOUS
DAMAGE TO YOUR VEHICLE AND/OR ANOTHER VEHICLE.
MATERIALS NEEDED: Hammer, center punch, pencil
MATERIALS FURNISHED: One hardware pack, two end
castings, four Rota castings, cross bar, instruction page.
ROTA LIGHT BAR MOUNTING INSTRUCTIONS
Part No’s: 210871, 210872 & 210874
This is the open end of the Mounting End
Casting. Measure from this point on each
Mounting End Casting. (See below on Light Bar
Cutting Instruction)
ROTA LIGHT BAR CUTTING INSTRUCTIONS
1. Two people will be needed to complete this task.
2. Place ONLY THE MOUNTING END CASTINGS with the Rubber Booties into the
rain-gutters of your vehicle.
3. Level each Mounting End Casting so that the top flat area is parallel to the horizon.
4. Take a tape measure and measure the distance between each open end of each
Mounting End Casting.
5. From that dimension subtract 2 inches.
6. Subtract that total from the total length of the bar, which is 56".
7. Take the difference and divide it by two.
8. The amount divided by two is the amount you will cut off each end of your bar.
9. Measure and mark a line on both ends of the steel bar using the above dimension
you have just figured.
10. Clamp one end of a bar into a vise. (Be careful not to scar the light bar).
11. Using a hacksaw, cut carefully along the marked lines. (If a vise is not available, put
the bar on a table, secure tightly and cut).
12. Repeat steps 9-11 for the other end of the bar.
SPECIAL NOTE: VEHICLES NOT HAVING RAIN GUTTERS WILL REQUIRE RAIN GUTTER KITS:
#220042 76-93 Chevy S-10/Sonoma P/U, Blazer/Jimmy, ’09-13 Dodge FS 1500 P/U All Cabs, 04-08 F-150
N.Body, 84-02 Isuzu Trooper, 97-02 Mitsub. Mont.Sport, 05-13 Toyota Prerunner Cr.Cab, 07-13 Tundra,
05-07 4-Runner, 07-13 FJ Cruiser
#220052 04-13 Chevy Colorado/GMC Canyon, 97-04 Dodge Dakota, 99-13 Ford Super Duty All Cabs, 00-05 Ford
Excursion, 91-02 Isuzu Rodeo/Amigo, 05-13 Jeep Grand Cherokee, 83-93 Mazda B-Series P/U, 98-13
Nissan Frontier Reg.Cab, 02-13 Nissan Frontier Crew Cab, 00-13 Nissan Xterra-w/o Option Roof Rack,
86-01 Pathfinder, 86-97 Nissan Hard Body P/U, 89-95 Toyota P/U, 93-99 T-100, 84-04 Toyota 4-Runner,
96-04 Toyota Tacoma/Prerunner Crew Cab, 00-06 Toyota Tundra, 01-07 Toyota Sequoia.
#220062 04-13 F-150
#220542 00-13 Chevy/GMC Sierra/Silverado C/K P/U/FS, 02-09 Chevy Trail Blazer/Envoy , 02-
12/Avalanche/GMC/Denali Truck, 00-13 Chevy Tahoe/Suburban/Tahoe/GMC Yukon/Yukon XL, 02-08
Dodge FS 1500 P/U, 03-10 Dodge 2500/3500 P/U & Quad, 02-08 Dodge Quad 1500, 05-09 Dodge
Durango/Dakota, 06-13 Dodge Mega Cab 1500/2500/3500 Ram P/U
#221502 98-01 Dodge Quad Cab 1500 P/U, 98-02 Dodge Quad Cab 2500/3500 P/U, 94-02 Dodge 2500/3500 P/U
Old Body Style, 94-01 Dodge P/U.
#222742 91-01 Ford Explorer(not Eddie Bauer)/Mercury Mountineer, 91-94 Mazda Navajo,
#223412 88-99 Sierra Silverado C&K P/U/FS, 92-99 Chevy Suburban/Yukon/Tahoe, 93-98 Jeep Grand Cherokee
Rota Hood Casting - 1
Rota Angle Casting - 2
Mounting End Casting - 3
Cross Bar
“L” Shaped Steel
Bracket
3/8” Bolt
Rubber Bootie
¼” Bolts
Welded Nut Washer
For the proper installation of
this light bar, orientation of this
washer must be as shown in this
drawing