Security Chain Co (SCC) Auto-Trac - Manual

Vehicle wheel clearance for
traction devices is the respon-
sibility of the automobile
manufacturer. Please refer to
your vehicle owner’s manual
for more information on the
use of tire chains. AUTO-TRAC™
Tire Chains are designed to
meet S.A.E. class “S” clearance
requirements.
Always practice installing new chains before you
actually need them. Tire sizes can vary by manufac-
turer, therefore a proper fit can only be assured with
a pre-fit test on the tire.
If you are installing used chains, carefully inspect them
for any worn chains and damaged components.
Tire Chains are not to be used on snow tires.
Never exceed 30 MPH while the AUTO-TRAC™
Chains are installed. Accelerate slowly and evenly.
Avoid spinning your tires. The life of your chains will
vary according to road conditions, driving speed and
individual driving habits.
The following are some activities that can cause
unnecessary wear to your tire chains:
• Locking your wheels when braking
• Driving on bare pavement that is not
covered with snow or ice
• Hitting curbs
• Installing the chains improperly
• Loose of improperly fitted chains
Caution: Tire chains are designed only to provide
extra traction in severe weather emergencies.
Drivers should always exercise caution and observe
driving conditions during hazardous weather. Please
use good judgement in using this product. In the
event that a cross chain should break, immediately
pull off the road to a safe place and remove, tie
back, or repair the broken component. Do not
continue driving with a loose or broken cross chain.
Use tire chains as a traction device. Do not use them
for any other purpose, including towing or lifting.
(A) DISCLAIMER OF WARRANTIES:
Peerless warrants free from defects in
workmanship and materials for 90 days from
purchase date of this product to owner. Warranty
does not include damage due to product failure,
misuse, abuse or cost of inconvenience. No other
express warranty is given and no affirmation, by
words or action, shall constitute a warranty.
(B) REMEDIES:
The buyer’s sole remedy for breach of any warranty
is limited exclusively to obtaining, at the discretion
of the seller, either credit or repair or replacement
of any product sold hereunder and manufactured
by Peerless Chain Company within 90 days after
deliver to the owner. Defective product may be
brought to the place of purchase, or returned,
freight prepaid to: Peerless Chain Company,
1416 E. Sanborn Street, Winona, MN 55987
SPEEDS OVER 30 MPH, IMPROPER INSTAL-
LATION OR IMPROPER FIT VOIDS WARRANTY.
Although this warranty gives you specific rights, you
may have other legal rights which differ from state
to state. For more information please write:
Peerless Chain Company, 1416 E. Sanborn Street,
P.O. Box 5349 Winona, MN 55987-5349
LIMITED WARRANTY
• Lay the chains out on a flat
surface, remove all tangles and
ensure the side wire hooks are facing down.
Do not drive with chains that are damaged.
• Slide the inside side cable (A) and chain behind the
wheel. Find the split (B) in the front side chain. Lay
one half of the chain in front of the tire and the other
behind the tire.
1. Park your vehicle with the green side-chain connector (F) at the 1:00 o’clock position. This will ensure easy
removal of the tire chains without re-positioning your vehicle. CAUTION: Park your vehicle off-road with the engine
off and the emergency brake set before removing your AUTO-TRAC™ chains.
2. Grasp the bottom tensioner (H) and flip the red lever up to remove. Pull the red cable out of the side-chain
connector (I ). Firmly grasp the red cable end and flip the red lever down to take up the exposed cable.
PINCH WARNING: Keep your fingers clear of the cable while allowing the cable to re-seat into the tensioner.
3. Grasp the top tensioner (E) and flip the red lever up to remove. Pull the red cable end out of the side-chain
connector (F). Firmly grasp the red cable end and flip the red lever down to take up the exposed cable.
PINCH WARNING: Keep your fingers clear of the cable while allowing the cable to re-seat into the tensioner.
4. Bring the back side cable forward and disconnect (Refer to step 2 photo).
IMPORTANT
- Follow All Directions Carefully When Installing AUTO-TRAC
™
PEERLESS
CHAIN & MATERIAL HANDLING
USE THIS AS A GROUND COVER WHILE INSTALLING YOUR AUTO-TRAC ™
• Bring the ends of the side cable
in front of the outer side wall.
• Connect the side cable together by inserting the knob
into the key-hole latch (C) • Leave the connected side
cable draped over the outer sidewall (D) while you
complete step 3.
• Grasp the top tensioner (E)
and flip the red lever up to
install. Pull the red cable end out and attach to the
green side chain connecter (F).
• Grasp the bottom tensioner
(H) and flip the red lever up to
install. Pull the red cable end out and connect to the
side chain connector (I). PINCH WARNING: Keep your
fingers clear of the chain and tensioner while engaging
the tensioners.
• Flip the red lever down to
tighten both the top and
bottom tensioners. Your chains will begin to self tighten.
CAUTION: You could damage your side
walls if the side wire hooks are not facing
out, away from the tire.
Park your vehicle off-road with the engine off and the emergency brake set before installing or removing your AUTO-TRAC™ chains.
IMPORTANT
INFORMATION:
• Leave the red lever in the
up position and slide the side
cable to the back of the tire (G), ensure the chain is
centered on the tire.
F
E
D
C
B
A
G
H
I
E
NOTE:
Face hooks out!
NOTE:
Face hooks out!
w w w . p e e r l e s s c h a i n . c o m
AUTO-TRAC ™ Chain Removal Instructions
™
Installation Instructions
PER003_instructions_q5r.qxd 4/3/06 5:18 PM Page 1