Mountain Off Road SB7686 - Manual (Page 2)

STEP 3: Locate the ¼" bracket to box spacer, 1-½" bolt, flat washer and lock washer. Put the lock-
washer then the flat washer onto the bolt and insert through the hole on the bracket that is labeled #1 in figure
2, with the flat edge of the spacer facing the bracket. See figure 2. (Note that the spacer goes on the opposite
side of the bracket from the washers). We recommend a dab of thread locking compound (Lock-Tight) be
placed on all of the mounting bolts. Now loosely thread the bolt into the hole of the steering box. Now all remain-
ing box to bracket bolts and spacers can be assembled in the same manner. Pay careful attention to assure that
the flat side of the spacers are facing the bracket. Once all four bolts are in, torque to approximately 45 ft/lbs.
STEP 4:
This step will be much easier with someone to assist in holding up the bracket while the bolts
are started. Lift assembly into position and align top two holes on the bracket with the existing holes in cross-
member. Loosely start both 1" bolts with flat and lock washers from the top. Tighten these bolts down to finger
tight only (these should not be tightened until all other bolts and spacers are in place.) Place remaining spacer
(bracket to frame) between frame and bracket aligned with the rearmost hole. Front two holes of bracket should
be aligned over the shackle mount (or Shackle Reversal System front pivot bracket). Insert 1-½" bolts using flat
and lock washers through all three holes and finger tighten. Tighten bolts through crossmember first and then
bolts through the frame. Torque bolts on crossmember to 45 ft/lbs. and bolts on frame to 35 ft/lbs.
Final Notes:
Start vehicle and turn wheels lock to lock several times to check for any signs of binding or un-
usual noises. Torque on all bolts should be checked after the first few hours of use and then periodically after
that.
FIGURE 2
This picture shows
the H.D. Bracket
as it would be
installed in the
Jeep. The thin
spacer is placed
on the upper left
mounting
bolt.
(#1).
FIGURE 1
This picture shows
the optional 3rd
mounting location
that you must drill
a hole in the
crossmember for.
#1
PAGE 2 of 2
TERMS/POLICIES:
RETURNS: No returns will be accepted without prior permission from M.O.R.E.™ LLC. You must call for a Return Goods Authorization (RGA)
number. Merchandise must be returned prepaid and insured. A claim must be made with in 30 days from receipt of merchandise. The original
invoice or a copy with the RGA number written on must accompany all returns. A 20% restocking fee will be charged on all parts returned for
credit or refund unless merchandise is proven to be defective or was shipped wrong by M.O.R.E.™ LLC. No merchandise will be issued credit
or refund if it has been installed, modified, used in any way or is in unsalable condition.
WARRANTY: All merchandise is warranted to be free from defects in materials and workmanship prior to installation. Any alteration or im-
proper use will void this warranty. Because all parts we sell are intended for use in heavy-duty applications it is not possible to warrantee or
guarantee the performance of any items. M.O.R.E.™ LLC. products and the products manufactured by others, which we sell may be subject
to an infinite variety of conditions due to the manner in which they are used, serviced and/or installed. Purchasers and users of such products
rely upon their own judgment as to the suitable use selection, service and installation of such products.
PRODUCT DISCLAIMER: Modification of your vehicle to enhance performance with parts sold by M.O.R.E.™ LLC. may create a dangerous
condition which could cause serious bodily injury, and the buyer hereby expressly assumes all risks associated with any such modifications.
All parts sold by M.O.R.E.™ LLC. are for racing or off road use only. Mountain Off Road Enterprises LLC. will not accept responsibility for
personal injury or property damage arising from the failure of any parts manufactured or sold by M.O.R.E.™ LLC.
Specifications are subject to change without notice.
These instructions, and the M.O.R.E.™ logo are copyright©, 2008.