Smittybilt T0654FJ Nerf-Step - Manual

For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 1600 Walnut Parkway, Compton, CA 90220
Installation Instructions
Nerf Step (Part # T0654FJ)
04-08 Toyota FJ Cruiser
NOTE: Carefully read entire instructions thoroughly before attempting to install this part.
Parts Included Qty Tools Needed
8mm x 1” bolt 10 13mm Wrench
5/16” Flat Washer 10
8 mm Lock Washer 10
STEP 1: Remove the bars from the box and locate the hardware.
STEP 2: Identify the Driver and Passenger; the short end goes towards the front of the vehicle.
STEP 3: Remove the plastic cap between the pinch-weld and the underside floor pan.
STEP 4: Line up the bracket holes and insert hardware. Do not tighten completely at this time.
STEP 5: After all bolts have been placed, tighten the front bolt first and then the rear. Then proceed to
Completely tighten the remaining bolts. Repeat same process for opposite side.
Product cleaning and maintenance instructions
Stainless Steel Finish – Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap, window or glass cleaner may be used to clean
the finish. Dual state powder coat finish – Mild soap, window or glass cleaner may be used to clean the finish. In order to protect the finish, you may wax your
product on a regular basis with pure carnauba automotive wax. Do not use any types of soap, polish or was that contains abrasive that could damage the finis
WARRANTY
Smittybilt’s products are covered under the following limited warranties only. Note that the duration of the limited warranty differs according to the material and finish of the product
purchased. Subject to the duration and conditions of the limited warranty stated below, Smittybilt warrants to the original retail purchaser that its products are free from defects in material
and workmanship. All other warranties and representations express or implied are hereby disclaimed, including fitness for merchantability and buyer’s intended use or purpose. All parts
are sold “AS IS” except for the limited warranties granted herein. Buyer assumes all risks as to the selection, suitability and performance of all goods and products selected. This limited
warranty does not cover damage or impairment in any part due to misuse, improper installation, accident or contact with on-road or off-road hazards, product modification, improper or
inadequate cleaning and/or maintenance. Smittybilt is not responsible for items damaged during shipping. This warranty is not transferable from the original buyer. For the original Buyer
to be eligible for the limited warranty coverage, the Buyer must provide proof of purchase. Smittybilt strongly recommends returning the warranty registration card.
Customer’s remedy hereunder shall be limited only to repair or replacement (at Smittybilt’s option) of any defective part(s) returned to Smittybilt at customer’s expense. The determination
of whether or not a returned part is defective or subject to coverage under the limited warranties stated herein shall be made at Smittybilt’s sole discretion.
1. Limited Lifetime Warranty on Stainless Steel Products -
Smittybilt stainless steel products carry the foregoing limited repair or replacement warranty against workmanship and defects in the material so long as the original purchaser retains the
original stainless steel parts.
2. Limited Five (5) Year / 50,000 Mile Pro-Rata Warranty (whichever occurs first) on Dual-Stage Powder Coating Products -
Smittybilt dual-stage powder coated products carry the foregoing limited repair or replacement warranty for a period of (5) years or 50,000 miles (whichever occurs first) from date of
purchase against workmanship and defects in the material, provided that any claim submitted after (2.5) years from date of purchase shall, if accepted, be satisfied by Smittybilt offering
customer a credit on the purchase of a replacement product equal to fifty percent (50%) of customer’s initial purchase price.
Fichter Design's configuration protected by International Trade Dress Law. Fichter Designs licensed to Smittybilt Automotive Products are Protected
by U.S. patent law and International Copy Right Law. US Patent #6588783 and #6874801 other patents and continuances pending. All Intellectual
Property & Patent infringements will be prosecuted to the full extent of the law.