Aries Automotive S226008-2 - Manual

08/S226008-2 PART # S2260
Page - 1 -of 2
2009-12 HONDA PILOT
2 12mm x 50mm Bolt Plates 10 10mm Lock Washers
brackets and attach it using the included (4) 10 mm x 25mm Hex Head Bolts, (4) 10mm x 22mm OD Flat Washers, and (4)
10mm Lock Washers (Figure 5) . Snug but do not tighten.
(2) 12mm Flat Washer, (2) 12mm Lock Washer and (2) 12mm Nut, Carefully position the driver sidebar onto the mounting
Washer, (1) 10mm Lock Washer and (1) nut,
2 10mm x 40mm Bolt Plates (rounded end) 4 8mm Flat Washers
1 Driver/Left Sidebar 4 12mm Hex Nuts
4 12mm Lock Washers 4 8mm Lock Washers
Determine the driver/left rear mounting bracket from the illustration on Page 1 and hang it from the two bolt plates using
hole located on the bottom of the body next to the pinch weld. Rotate the Bolt Plate 90-degrees or until it stops turning.
. Next insert the 12mm Centered Round End Bolt Plate into the round frame channel and rotate 90-degrees,
Next, move to the driver/left rear of the vehicle. Insert the 12mm Bolt Plate into the oval hole located on the bottom of the
10mm Lock Nuts. Next hang the Support Bracket from the previously installed Bolt Plate using (1) 10mm x 26mm OD Flat
Front Mounting Bracket and bolt together with (2) 10mm x 35mm Hex Bolts (4) 10mm x 26mm OD Flat Washers and (2)
om the illustration on Page 1. Line up the two holes in the bracket with the
do not tighten at this time,
two holes using the provided (2) 8mm x 25mm Hex Bolts, (2) 8mm Flat Washers and the 8mm lock Washers. Snug but
the inner rocker pannel. Position the driver side Front Mounting Brackets up to vechile. Hang the mount bracket from the
Next, locate the two threaded holes, one located on the bottom of the floor rocker pannel, the other located on the side of
10mm round End Bolt Plate into the hole and rotate clock-wise 90-degress or until it stops turning,
Starting on the driver side front of the vehicle, locate the round hole on the bottom of the inner frame channel. Insert the
PARTS LIST:
1 Passenger/Right Sidebar 4 12mm Flat Washers
1 Driver/Left Front Mounting Bracket 2 10mm Nuts
1 Passenger/Right Front Mounting Bracket 10 10mm x 26mm O.D Flat Washers
1 Driver/Left Front Frame Bracket 4 10mm x 35mm Hex Bolts
1 Passenger/Right Front Frame Bracket 4 10mm Lock Nuts
1 Driver/Left Rear Mounting Bracket 8 10mm x 25mm Hex Bolts
1 Passenger/Right Rear Mounting Bracket 8 10mm x 22mm O.D Flat Washers
2 12mm x 40mm Bolt Plates (square end) 4 8mm x 25mm Hex Bolts
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ
INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
2.
(Figure 1)
. 3.
(Figure 2) .
4. Determine the driver side Front Frame Bracket fr
INSTALLATION INSTRUCTIONS
ARIESOFFROAD
Passenger Side Rear
Mounting Bracket Driver Side Rear
Mounting Bracket
Driver Side Front
Frame Bracket
Passenger Side Front
Frame Bracket
Passenger Side Front
Mounting Bracket
Driver Side Front
Mounting Bracket
Rear
Front
Driver Sidebar
Passenger Sidebar
12mm Bolt Plate
10mm Centered Bolt Plate
12m Bolt
Plate
(Figure 3) . Snug but do not tighten at this time.
5.
(Figure 4)
6. Align Sidebar properly, and then tighten all hardware.
7. Repeat steps 2 - 8 for the passenger Sidebar.
8. Do periodic inspections to the installation to make sure that all hardware is secure and tight.