Advance Adapters 7155730 User Manual
Toyota l/c transfer case twin stick
ADVANCE ADAPTERS INC.
P/N: 715573
P.O. Box 247, 4320 Aerotech Center Way
New Item: (8/02)
Paso Robles, CA 93447
PAGE 1 OF 5
Telephone: (800) 350-2223
Fax: (805) 238-4201
Page Rev. Date:
03-17-11
SPECIAL NOTE:
The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will
void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend
that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a
service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive
dealerships and parts stores.
KIT CONSITS OF:
No:
Qty
Part No.
Description
1.
1
*
715575
HIGH LOW PIVOT BLOCK
2.
1
715576
T/C HIGH LOW SHIFTER LEVER
3.
1
*
715577
2WD/4WD PIVOT BLOCK
4.
1
715579
PIVOT SHAFT
5.
2
715580
3/8"-24 BALL JOINT (High/Low linkage)
6.
1
715581
5/16"-24 BALL JOINT (Mode shift handle)
7.
1
715582
5/16"-24 MALE HEIM (Mode shaft)
8.
2
715583
SHIFT KNOB
9.
1
715585
TRANSFER CASE MODE SHAFT
10.
1
*
715586C
HIGH/LOW SHIFT HANDLE (Must be welded to 715575)
11.
1
*
715586C
MODE SHIFT HANDLE (Must be welded to 715577)
12.
1
*
715588C
MODE SHIFT LINK (Must be welded to 715577)
13.
1
715589
CLEVIS PIN
14.
1
715590
COTTER PIN
15.
4
**
715591
(FJ4404) PIVOT BUSHING
16.
1
723101
5/16"-18 NUT (Pivot pin)
17.
1
723103
5/16" LOCK WASHER
18.
1
723122
5/16" FLAT WASHER (Pivot pin)
19.
1
723131
5/16"-24 JAM NUT (Mode link)
20.
2
723719
3/8"-24 JAM NUT(High/Low link)
21.
1
723769
3/8"-24 SET SCREW (High/Low shift lever)
22.
1
723770
3/8"-24 X 7.5" ALL THREAD (High/Low link)
23.
1
302060
TWIN STICK BOOT
24.
1
302063
BOOT RING
25.
2
303121
1/2"-13 JAM NUT (Shift Knobs)
*
ITEMS MUST BE WELDED BEFORE INSTALLING
**
ITEMS MUST BE INSTALLED AFTER WELDING
**715591 IS A PRESS FIT INTO THE PIVOT BLOCK
NOTES:
This assembly will require the installation of a new mode
shaft into the transfer case. Refer to the exploded assembly
view on the following pages for part identification and part
assembly.
This kit is a universal type kit that requires the handles
to be bent and welded to fit your vehicle.
APPLICATIONS:
1) GM V8 with a TH350 or 700R transmission
and our T/C adapter.
Note:
4L60E transmissions with the
Mark's adaptor should use P/N 715573B.
TOYOTA L/C TRANSFER CASE TWIN STICK
We do offer aluminum shifter knobs for
the Toyota twin stick kits. These knobs
are sold separately under Part No. 715584
at a price of $42.95