BOB Sun Shield OMA12A - Manual

Congratulations on your
purchase of the BOB Sun
Shield. It is designed to
protect your child’s delicate
eyes and skin from heat,
glare, and ultraviolet
(UVA/UVB) rays.
It also provides protection
from wind and flying
insects. Proper installation
and care will provide years
of reliable service.
Before attempting to use
or attach your new Sun
Shield, read and
understand these
instructions completely
to insure proper
assembly and operation.
If you are unclear on any
point, contact your dealer
or BOB before use.
Warnings
. This product is designed
exclusively for use with
BOB Duallie and
Ironman Duallie
strollers. It is not
intended for use with
other strollers or
products.
. The Sun Shield is not
designed to work with
optional Infant Car Seat
Adapter and car seat.
. Never leave child
unattended.
. The Sun Shield reduces
the exposure to sun and
heat but does not
eliminate it. Avoid
exposing your child to
prolonged sun and heat.
. It is possible for small
insects to enter through
the small gaps between
the shield and the stroller.
. When not in use, keep
out of reach of children.
. When the Sun Shield is
used, the rear canopy
flap must be in correct
position as described
below. This will insure
proper air flow and
ventilation for your child.
INSTALLATION
INSTRUCTIONS:
1. Set stroller Parking
Brake (refer to Parking
Brake section of stroller
Owner’s Manual). Place
each sun canopy into
position to receive the Sun
Shield as shown in Fig.1.
2. Pull each canopy
drawstring in order to
gather extra material under
canopy. Cinch cord lock
against canopy to retract
and hold material, as
shown in Fig. 2.
3. Locate rear canopy flap
and fold forward. Attach
canopy flap Velcro on flap
to respective Velcro mate
on top outboard side of
each canopy as shown in
Fig. 3). Warning tag on rear
canopy flap also describes
and illustrates this critical
step.
Very Important: When the
Sun Shield is used, the
rear canopy flap must be
in correct position as
described below. This
will insure proper air flow
and ventilation for your
child.
4. Inspect opening at back
of stroller to make sure the
air passages between top
of seat back and canopy
are unobstructed (see Fig.
4). We recommend
reclining each seat back
slightly to optimize airflow
(refer to Reclining Seat
section of stroller Owner’s
Manual).
5. Place Sun Shield on the
stroller so the rear flap
drapes over back (between
the handlebars) and the
seam above the window is
aligned with the forward
Sun Canopy supports (see
Fig. 5).
6. Stretch the elastic cord
on each side under each
respective black shock
knob as shown in Fig. 6.
There is an opening mid
way up each side (with
silver reflective fabric on
each end) where the elastic
cord is exposed.
7. Attach each looped end
of the elastic cords
(800) 893-2447 www.bobgear.com email- [email protected] Ph: (208) 375-5171
Fax: (208) 375-5172, BOB Trailers, Inc. 5475 Gage St. Boise, ID 83706
du duallie sun shield ins allie sun shield instr tructions uctions
Rear
Canopy
Flap
Fig. 1 Canopy Supports in position.
Aft Canopy
Supports fully
rotated back
Forward Canopy
Supports
Cinch each
Cord Lock
tight against
each Canopy
Fig. 2 Canopy Drawstring Adjustment
Fig. 3 Rear Canopy Flap in position.
Velcro
Fastened
Velcro
Fastened
Rear Canopy
Flap folded
over top
Fig. 4 Rear Vents unobstructed.
Air Passages
Fig. 5 Shield placed on Canopy
Align Sun
Shield
Seam with
Forward
Canopy
Supports
Elastic
Cord
End
Loop
Fig. 8 Elastic properly routed
under frame sides and ends.
Fig. 7 Front attachment:
Insert Stay ends into holes.
Ends of metal Stay
plastic Plugs with holes
Fig. 6 Elastic cord attachment
Silver
Reflective
Fabric
Elastic Loop
Around Black
Shock Knob
Elastic Cord
Under Black
Shock Knob
OMA29 P1