Advance Adapters 713096 - Manual

ADVANCE ADAPTERS INC. P/N 713096
P.O. Box 247, 4320 Aerotech Center Way
Paso Robles, CA 93447
PAGE 1 OF 4
Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 09-17-12
SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the
components will void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion,
we strongly recommend that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter
components. We recommend that a service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment.
These manuals are normally available at automotive dealerships and parts stores.
KIT CONSISTS OF:
No. Qty Part No. Description
INSTALLATION INSTRUCTIONS: We recommend that your Jeep TJ have
1” of body lift before starting. The front suspension may need to be adjusted to
allow for the additional engine weight.
This motor mount is designed to work with
a 1997-2006 4 cylinder steering bracket, Part# 52058855AB. If your replacing a 6
cylinder, you will need this Jeep part number or our 713093P.
New Mount Installation:
Refer to the owner’s manual for the stock engine removal. Once the stock engine is removed, cut the original motor
mounts from the frame. Also remove the steering pillow block bracket and discard. Clean all remnants of weld so that the
frame is smooth. Make sure that the frame surface for the mounts is bare metal so that there are no contaminants in the
weld area. The TJ frame has a small hole on both sides that originally held the brake lines. By removing the brake line
mounting bracket you expose the hole that is used for our fixture bracket. Take the fixture bracket and lay it on the frame
using the 1/4” bolt as a dowel. Lay the new motor mount frame bracket over the frame and slide it towards the front until
it hits the fixture. Clamp or tack weld the mount to the frame. Do not weld the fixture
bracket to the frame. It is only used to locate the new motor mount. Repeat the
clamping and/or welding procedure for the other side. When both sides are in a fixed
position, use a tape measure and check from the center of the passenger side hole to the
center of the driver’s slot. You should come close to 19.5”. It is also a good idea to
check to see if both of the new frame mounts are located the same distance back on the
frame. Next, verify that the steering pillow block fits to our mount, (6 cylinder Jeeps
must purchase the 4 cylinder pillow block listed above) without any interference. When
the mounts have been correctly positioned, weld them in place and paint.
CHEVY 4.3L V-6 ENGINE
TJ WRANGLER MOTOR MOUNTS
1. 2 713092A BOLT SLEEVE
2. 4 713092B MOTOR MOUNT BUSHING
3. 1 713092C MOTOR MOUNT FRAME FIXTURE
4. 1 713092L MOTOR/TJ FRAME MOUNT (Driver’s)
5. 2 713092M ENGINE MOUNT (Right & Left)
6. 1 713092R MOTOR/TJ FRAME MOUNT (Passenger)
7. 4 713092S SPACERS FOR TJ MOUNTS (both left and right)
8. 8 720038 10MM LOCK WASHER
9. 8 720044 10MM-1.5 x 20MM(plate mounting)
10. 2 723704 3/8” LOCKWASHER (pillow block)
11. 2 723721 3/8”-16 x 1” H.H.C.S. (pillow block)
12. 2 723735 3/8” FLAT WASHER (pillow block)
13. 6 723718 3/8”-16 x 1” F.H.C.S.
14. 4 725003 1/2” FLAT WASHERS
15. 2 725005 1/2”-13 NYLON LOCK NUT
16. 2 725027 1/2”-13 x 5” H.H.C.S.
17. 1 713096L MOTOR MOUNT PLATE (left)
18. 1 713096R MOTOR MOUNT PLATE (right)