Blue Rhino OUTDOOR LP GAS LANTERN GLL905W - Manual (Page 2)

WARNING
FOR YOUR SAFETY:
For Outdoor Use Only
(outside any enclosure)
DANGER
If you smell gas -
1. Do not attempt to
light appliance.
2. Extinguish any open
flame.
3. Disconnect from fuel
supply.
DANGER
CARBON MONOXIDE
HAZARD
• This appliance can
produce carbon
monoxide which has
no odor.
• Using it in an
enclosed space can
kill you.
• Never use this
appliance in an
enclosed space such
as a camper, tent, car
or home.
WARNING
FOR YOUR SAFETY:
Do not store or use
gasoline or other liquids
with flammable vapors
in the vicinity of this or
any other appliance.
DANGER: Failure to follow these
instructions, dangers, warning and cautions
in this manual may result in serious bodily
injury or death, or in a fire or an explosion
causing damage to property.
WARNING:
This lantern is for outdoor use only, and
shall not be used in a building, garage or
any other enclosed area.
Do NOT operate, light or use this appliance
within 8 feet of walls, structures or
buildings.
This lantern is NOT for commercial use.
This lantern is for use with liquid propane
(LP) gas only. The conversion to or
attempted use of natural gas in this LP gas
lantern is dangerous and will void your
warranty.
LP gas Characteristics:
a. LP gas is flammable and hazardous if
handled improperly. Become aware of
the characteristics before using any LP
gas product.
b. LP gas is explosive under pressure,
heavier than air, and settles and pools in
low areas.
c. LP gas in its natural state has no odor.
For your safety, an odorant is added that
smells like rotten cabbage.
d. Contact with LP gas can cause freeze
burns to skin.
Do not store spare LP cylinder within 10
feet (3.05 m) of this appliance.
An LP cylinder not connected for use shall
not be stored in the vicinity of this or any
other appliance.
LP gas tank needed to operate. Only tanks
marked “propane” may be used.
The LP gas tank used with the lantern must
be constructed and marked in accordance
with the Specifications for LP-gas cylinders
of the U.S. Department of Transportation
(DOT) or Transport Canada,
CAN/CSA B339.
LP gas tank must be arranged for vapor
withdrawal.
Dented or rusted LP gas tanks may be
hazardous and should be checked by your
LP gas supplier prior to use.
The LP gas tank should not be dropped or
handled roughly.
LP gas tanks must be stored outdoors out
of the reach of children and must not be
stored in a building, garage, or any other
enclosed area. Your tank must never be
stored where temperatures can reach over
125°F.
Never attempt to attach this lantern to the
self-contained LP gas system of a camper
trailer, motor home or house.
The use of alcohol, or prescription or
non-prescription drugs may impair the
consumer’s ability to properly assemble or
safely operate the appliance.
Never use lighter fluid, gasoline, kerosene
or alcohol with this product.
Your lantern has been checked at all
factory connections for leaks. Recheck all
connections, as movement in shipping can
loosen connections.
Check for leaks even if your unit was
assembled for you by
someone else.
Do not operate if gas leak is present. Gas
leaks may cause a fire or explosion.
You must follow all leak-checking
procedures before operating. To prevent fire
or explosion hazard when testing for a leak:
a. Always perform leak test before lighting
the lantern and each time the tank is
connected for use.
b. No smoking. Do not use or permit
sources of ignition in the area while
conducting a leak test.
c. Conduct the leak test outdoors in a well-
ventilated area.
d. Do not use matches, lighters, or a flame
to check for leaks.
e. Do not use lantern until any and all leaks
are corrected.
If you are unable to stop a leak, disconnect
the LP gas supply. Call a gas appliance
serviceman or your local LP gas supplier.
Do not use in an explosive atmosphere.
Keep lantern area clear and free from
combustible materials, gasoline and other
flammable vapors and liquids.
Keep all combustible items and surfaces
at least 21 inches (53 cm) away from the
lantern at all times. DO NOT use this lantern
or any gas product under any overhead
or near any unprotected combustible
constructions.
It is essential to keep the lantern’s valve
compartment, burners, and circulating air
passages clean. Inspect lantern before
each use.
Do not alter lantern in any manner.
Do not use the lantern unless it is
COMPLETELY assembled and all parts are
securely fastened and tightened.
This lantern should be thoroughly cleaned
and inspected on a regular basis.
Use only the valve provided. The
replacement valve shall be that specified by
the manufacturer.
Use only Blue Rhino Global Sourcing, Inc.
factory authorized parts. The use of any
part that is not factory authorized can
be dangerous. This will also void your
warranty.
Do not use this appliance without reading
“Operating Instructions” in this manual.
Do not touch metal parts of lantern until
it has completely cooled (about 45 min.)
to avoid burns, unless you are wearing
protective gear (pot holders, gloves, BBQ
mittens, etc.).
Do not install or use in or on boats or
recreational vehicles.
When using, fire extinguishing materials
shall be readily accessible.
Do not use lantern in high winds.
Never lean over the lantern when lighting.
Do NOT use this lantern if any part has
been under water. Immediately call a
qualified service technician to inspect the
appliance and to replace any part or control
system and any gas control which has been
under water.
Do not leave a lit lantern unattended,
especially keep children and pets away
from lantern at all times.
Allow the lantern to cool before storing.
Storage of lantern indoors is permissible
only if the tank is disconnected, removed
from the lantern and properly stored
outdoors.
Do not attempt to disconnect the gas
regulator from the tank or any gas fitting
while the lantern is in use.
Disconnect cylinder when not in use.
Use of chain: Always hang lantern from a
sturdy, non-combustable support or use
with optional base (part number 55-09-287,
not included).
Use of base: Always use your lantern on a
hard, non-combustable, level surface. An
asphalt or blacktop surface may not be
acceptable for this purpose.
Do not use directly on wooden decks and
wooden picnic tables.
Keep all electrical cords away from a hot
lantern.
Do not use lantern for indoor heating.
TOXIC fumes can accumulate and cause
asphyxiation.
After a period of storage and/or nonuse,
check for leaks, and burner obstructions.
If lantern is not in use, the tank must
be disconnected and stored in a proper
location.
Do not store a spare LP gas tank under or
near this appliance.
Use protective gloves when assembling this
product.
Do not force parts together as this can
result in personal injury or damage to the
product.
Do not operate lantern with a hole or crack
in the mantle.
Do not attempt to operate the lantern
without a mantle installed.
Deaths, serious injury or damage to
property may occur if the above is not
followed exactly.
Operating Instructions
Lantern is inteded to hang from the chain on a non-
combustable, sturdy support, unless lantern is used
with optional base (part number 55-09-287, not
included).
This lantern is designed to operate with a one pound
7-3/8” high disposable / 16.4 oz. propane gas tank
(DOT 39 Cylinder).
DO NOT ATTEMPT TO REFILL ANY ONE POUND
(16.4 oz.) PROPANE GAS TANKS!
Connecting Gas Tank
1. Make sure the control knob is in the “OFF” position.
(Figure 1)
2. Lubricate the threads of the regulator valve
with petroleum jelly, insert the gas tank into the
regulator valve and hand-tighten firmly. (Figure 2)
3. Insert LP gas tank into the base.
4. Test for leaks
Checking for Leaks
WARNING: Failure to inspect this connection or
follow these instructions could cause a fire or
an explosion which can cause death, serious
bodily injury, or damage to property.
1. Make 2-3 oz. of leak solution by mixing one part
liquid dishwashing soap with three parts water.
2. Make sure control knob is “OFF”.
3. Attach LP gas tank, per “Connecting Gas Tank”
instructions.
4. Spoon several drops of solution, or use squirt
bottle, at the LP gas tank to regulator connection.
5. Inspect the solution at the connections, looking for
bubbles or the smell of rotten cabbage.
a. If NO bubbles appear or smells of rotten
cabbage, the connections are secure.
b. If bubbles appear, you have a leak.
1. Loosen and retighten this connection, making
sure the connection is secure.
2. Retest with solution.
If you continue to see bubbles after several
attempts, disconnect propane source and
contact 1.800.762.1142 for assistance.
Lighting
DO NOT expose the lantern to flammable
vapors or liquids during lighting.
1. Make sure all labels, packaging and protective
films have been removed from the lantern.
2. Make sure there are no obstructions of airflow to
the gas unit. Spiders and insects can nest within
and clog the burner / venturi tube at the orifice.
A clogged burner tube can lead to a fire.
3. Control knobs must be in the “OFF” position.
(Figure 1)
4. Attach the LP gas tank per the “Connecting Gas
Tank” instructions.
5. Igniter: Turn the control knob counterclockwise
to “ON” and repeatedly push the igniter button to
ignite the mantle.
Match: Wearing heat reistant gloves, position the lit
long match or lit long butane lighter evenly next to
the mantle. (Figure 3)
a. Turn control knob counterclockwise to “ON”.
b. Hold lit long match or lit long butane lighter next
to mantle for up to 5 seconds.
c. Remove long match/long butane lighter.
d. Replace cap.
Note: Once the mantle has been burned, it is very
fragile. Be careful not to touch it with finger or
match.
6. If ignition does not occur in 5 seconds, turn burner
control knob “OFF”, wait 5 minutes and repeat
lighting procedure.
Caution: If burner flame goes out during
operation, immediately turn the gas “OFF” and
let the gas clear for about 5 minutes before
re-lighting.
Turning Off
1. Turn control knobs to the “OFF” position.
2. Allow lantern to completely cool.
3. Remove LP gas tank and properly store tank.
Transporting
While Lantern is ON
1. Carefully carry the lantern by the chain.
2. Do not touch any of the lantern surfaces as they
may be hot
3. Before setting the lantern down, make sure the
lantern is hanging from a sturdy, non-combustable
support or the tank is properly in the base.
While Lantern is OFF
1. The LP gas tank must be removed and stored
properly.
2. Once the lantern is cooled, place the lantern (and
optional base) in a plastic bag and secure the bag
with a string.
DO NOT COMPLETELY SEAL THE PLASTIC BAG.
Note: The plastic bag will help protect from insects.
Replacing Mantle
1. Turn control knob to “OFF” and remove LP
gas tank.
2. Allow lantern to cool completely.
3. Open cap and remove globe
4. Attach mantle
Note: Tie the mantles around grooves in burner.
Note: Evenly distribute folds on mantle. Cut off the
extra string.
5. Insert globe and close cap
6. Perform leak check
Cleaning and Care
CAUTION: All cleaning and maintenance should
be done when lantern is cool and with the fuel
supply disconnected.
CAUTION: DO NOT clean any lantern part in
a self cleaning oven. The extreme heat will
damage the finish.
CAUTION: Keep lantern clear and free from
combusitble materials, gasolline and other
flammable vapours and liquids.
CAUTION: Do NOT obstruct the flow of
combustion and ventilation air.
Notices
1. Abrasive cleaners will damage this product.
2. Never use oven cleaner to clean any part of
lantern.
Inspecting
This lantern should be inspected on a regular basis to
ensure product safety and longer product life.
WARNING: Do NOT attempt to clean this lantern
unless the flames are COMPLETELY out and
unit is cool to the touch, about 45 minutes.
1. Check burner to make sure it is secure.
2. Check valve to make sure it is clear and free of
spider nests.
3. Check all gas connections for leaks.
4. Check components for any signs of damage or rust.
5. If damage to any component is detected, do NOT
operate until repairs are executed.
Cleaning Surfaces
WARNING: Do NOT attempt to clean this lantern
unless the flames are COMPLETELY out and
unit is cool to the touch. (About 45 minutes).
WARNING: Do NOT use oven cleaner or abrasive
cleaners as they will damage this product.
1. Wipe surfaces clean with mild dishwashing
detergent or baking soda.
2. For stubborn surfaces use a citrus based degreaser
and a nylon scrubbing brush.
3. Rinse clean with water.
Product Registration
For faster warranty service, register your product
immediately at www.bluerhino.com or call
1.800.762.1142.
Limited Warranty
Blue Rhino Global Sourcing, Inc (“Vendor”) warrants
to the original retail purchaser of this product, and to
no other person, that if this product is assembled and
operated in accordance with the printed instructions
accompanying it, then for a period of one (1) year from
the date of purchase, all parts in such product shall
be free from defects in material and workmanship.
Vendor may require reasonable proof of your date
of purchase. Therefore, you should retain your sales
slip or invoice. This Limited Warranty shall be limited
to the repair or replacement of parts, which prove
defective under normal use and service and which
Vendor shall determine in its reasonable discretion
upon examination to be defective. Before returning any
parts, you should contact Vendor’s Customer Service
Department using the contact information listed below.
If Vendor confirms, after examination, a defect covered
by this Limited Warranty in any returned part, and if
Vendor approves the claim, Vendor will replace such
defective part without charge. If you return defective
parts, transportation charges must be prepaid by you.
Vendor will return replacement parts to the original
retail purchaser, freight or postage prepaid.
This Limited Warranty does not cover any failures or
operating difficulties due to accident, abuse, misuse,
alteration, misapplication, improper installation or
improper maintenance or service by you or any
third party, or failure to perform normal and routine
maintenance on the product as set out in this owner’s
manual. In addition, the Limited Warranty does not
cover damage to the finish, such as scratches, dents,
discoloration, rust or other weather damage, after
purchase.
This Limited Warranty is in lieu of all other express
warranties. Vendor disclaims all warranties for
products that are purchased from sellers other than
authorized retailers or distributors, including the
warranty of merchantability or the warranty of fitness
for a particular purpose. VENDOR ALSO DISCLAIMS
ANY AND ALL IMPLIED WARRANTIES, INCLUDING
WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. VENDOR SHALL HAVE NO LIABILITY TO
PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL,
INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES. Vendor further disclaims any implied or
express warranty of, and assumes no responsibility
for, defects in workmanship caused by third parties.
This Limited Warranty gives the purchaser specific
legal rights; a purchaser may have other rights
depending upon where he or she lives. Some
jurisdictions do not allow the exclusion or limitation
of special, incidental or consequential damages, or
limitations on how long a warranty lasts, so the above
exclusion and limitations may not apply to everyone.
Vendor does not authorize any person or company
to assume for it any other obligation or liability in
connection with the sale, installation, use, removal,
return, or replacement of its equipment, and no such
representations are binding on Vendor.
Blue Rhino Global Sourcing, Inc
Winston-Salem, North Carolina USA
(800) 762-1142
Troubleshooting
Please visit www.bluerhino.com or call
1.800.762.1142.
OWNER’SMANU AL
MANUEL D’UTILISATION
MANUAL DEL USU ARIO
Manufactured in China for / Fabriqué en Chine pour / F abricado en China para:
Blue Rhino Global Sourcing, Inc
Winston-Salem, NC USA
1.800.762.1142, www .bluerhino.com
© Blue Rhino Global Sourcing, Inc. All Rights Reser ved / Tous droits réser vés / Todos los derechos reser vados
Save these instructions for future reference.
If you are assembling this unit for someone else, give this manual to him or her to read and sa ve for future
reference.
The use and installation of this product must conform to local codes. In absence of local codes, use the
National Fuel Gas Code, ANSI Z223.1/NFP A 54, CAN/CGA-B149.1, Natural Gas and Propane Installa tion Code.
California Proposition 65: Chemicals kno wn to the State of California to cause cancer , birth defects, or other
reproductive harm are created by the combustion of propane.
Certified Under / Homologué par / Certificado por:
ANS Z21.73b • CSA11.1b-2002 Camp Lights /
Lampes de camping / Lámparas para campamento
Conserve estas instrucciones para futuras consultas.
Si está montando esta unidad para otra persona, entréguele este manual para futuras consultas.
El uso e instalación de este producto ha de realizarse de acuerdo con los códigos locales. Si no existen
códigos locales, use las normas siguientes: Código Nacional para Gas y Combustibles, ANSI Z223.1/NFPA 54,
CAN/CGA-B149.1, Código de Instalación de Propano y Gas Natural.
Propuesta 65 de California: La combustión del propano crea productos químicos considerados por el Estado
de California como causantes de cáncer , malformaciones congénitas u otros daños reproductivos.
Conservez ces instructions afin de pouvoir les consulter ultérieurement.
Si vous êtes en train d’assembler cet appareil pour une autre personne, veuillez lui fournir le manuel afin
qu’elle puisse le lire et le consulter plus tard.
L’utilisa tion et l’installation de cet appareil doivent être conformes aux codes locaux. En l’absence de codes
locaux, suivez le Code national du gaz et des combustibles, les normes ANSI Z223.1/NFPA 54, CAN/CGA-
B149.1 et le Code d’installation du gaz naturel et du propane.
Proposition 65 de Californie: La combustion du propane produit des émana tions et des résidus chimiques
ayant été reconnus par l’Éta t de la Californie comme étant source de cancer, malforma tions congénitales et
autres domma ges reproductifs.
Outdoor LP Gas Lantern
Lanterne d’extérieur au propane
Linterna a gas propano líquido para exteriores
Model No. / Modèle nº / Modelo no. GLL905W
English – 1 English – 2 English – 3 English – 4 English – 5
GLL905W-OM-104 EFS
Exploded View & Hardware / Vue éclatée des pièces et quincaillerie /
Diagrama de explosión y elementos de ferretería
Figure 1
Figure 2
Figure 3
Match
Parts List / Liste des pièces / Lista de piezas
1 Cap* / Couverc le* / Ta pa* 55-10-013
2 Globe* / Globe* / Globo* 55-10-014
3 Chain* / Chaîne* / Cadena* 55-10-015
4 Wire Guard* / Protecteur métallique* / Resguardo de alambre* 55-10-016
5 Mantle* / Manchon* / Camisa* 55-10-017
6 Igniter* / Allumeur* / Encendedor* 55-10-018
7 Base / Socle / Base (Not Included / Non inc lus / No incluido) 55-09-287
8 Body* / Cuve du* / Carcass de la* 55-10-020
9 Control Knob* / Bouton de commande* / Perilla de control* 55-10-019
* Pre-assembled /Pré-assemblé / * Viene ensamblado
Exploded View / Vue éclatée / Diagrama de explosión
1
2
9
4
5
3
6
8
7
Optional Base / Socle en
option / Base opcional
Part number / numéro de pièce /
número de pieza: 55-09-287
Notes / Remarques / Notas: Notes / Remarques / Notas: