AIM Sports Red Lasers - Manual (Page 2)

LH001
Pistol Laser Sight
LH001 INSTRUCTIONS
INSTALLING LASER
1. Your laser comes with both a wire pressure switch and a toggle switch end cap. Unscrew the end
cap that came already attached to the laser, and insert the three batteries provided into the tube.
Make sure the + side is facing up on each battery.
2. Select the end cap one you would like to use, and install it by screwing it onto the rear end of the laser.
The laser can be activated by sliding the toggle bar or pressing the wire pressure pad.
3. Loosen the thumbscrew located on the right side of the mount until the laser body is able to slide
inside of it.
4. Locate the trigger guard mount, and unscrew and remove the two hex screws with the provided
wrench.
5. Place the half of the mount with the threaded hole in the center on the front of the trigger guard, and
the other half behind.
Note: There 10 plastic shims of different sizes included in the kit to be used to compensate for the
angle of the trigger guard if needed. If needed, select the appropriate sized shim, and insert it behind
the trigger guard and into the face of the back half of the mount. There are round dimples in the
mount that mate with the raised circular bumps on the shim that fit together.
7. Re-insert and tighten the hex screws with the wrench provided to secure the two halves of the mount
to the trigger guard.
8. Screw the laser into the threaded hole on the front of the mount.
ADJUSTING LASER
1. To adjust the laser, locate the hex screws located on the bottom and left side of the front of the laser.
2. To adjust the elevation up, tighten the hex screw with the provided wrench by turning it clockwise. To
lower the beam, turn the screw counter clockwise.
3. To adjust the windage to the right, turn the hex screw on the left side clockwise. To move the beam to
the left, turn the screw counter clockwise.
LH002 INSTRUCTIONS
INSTALLING LASER
1. Your laser comes with both a wire pressure switch and a toggle switch end cap. Unscrew the end
cap that came already attached to the laser, and insert the three batteries provided into the tube.
Make sure the + side is facing up on each battery.
2. Select the end cap one you would like to use, and install it by screwing it onto the rear end of the laser.
The laser can be activated by sliding the toggle bar or pressing the wire pressure pad.
3. Loosen the thumbscrew located on the right side of the mount until the laser body is able to slide
inside of it.
4. Locate the two small hex screws on the front of the laser, and ensure that one is positioned on the
bottom of the laser, and one is positioned on the left side. This will allow you to access these
adjustment screws for sighting in your laser later.
5. Slide the mount onto the accessory rail into the desired position
6. Tighten the hex screws with the wrench provided. to secure the mount to the rail.
ADJUSTING LASER
1. To adjust the laser, locate the hex screws located on the bottom and left side of the front of the laser.
2. To adjust the elevation up, tighten the hex screw with the provided wrench by turning it clockwise. To
lower the beam, turn the screw counter clockwise.
3. To adjust the windage to the right, turn the hex screw on the left side clockwise. To move the beam to
the left, turn the screw counter clockwise.
RED LASERS
CAUTION
Do not over tighten the screws or you may strip the
threaded holes. Stripped holes are NOT covered by warranty.
LH002
Pistol/Rifle Laser Sight
LH003
Tactical Red Laser
LH003 INSTRUCTIONS
INSTALLING LASER
1. Loosen the thumb screw located on the right side of the laser (laser pointing down range), and slide it
onto the accessory rail into the desired position.
2. Tighten the thumbscrew to secure the mount to the rail, using a coin or screwdriver if desired.
3. The laser can be activated by sliding the toggle bar located at the rear end of the laser back and forth.
4. The battery can be accessed by loosening the battery cap located on the bottom of the laser with a
coin or screwdriver.
ADJUSTING LASER
1. To adjust the windage, turn the hex screw located on the left front side of the laser. To move it to the
right, turn the screw clockwise with the provided wrench. To move it to the left, turn the screw counter
clockwise.
2. To adjust the elevation, turn the hex screw located on the bottom of the laser. To move the beam up,
turn the screw clockwise. To move it down, turn it counter clockwise.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.