AIM Sports Red Laser Scope - Manual (Page 2)

PARTS
• Objective lens
• Elevation turret
• Windage turret
• Tube
• Ocular lens/fine focus ring
SCOPE INSTALLATION
1. Using the provided hex wrench, loosen the screws on the sets of scope rings and
remove the top halves.
2. Loosen the ring’s base screw and widen the base so that it will fit onto the scope
mount rail.
3. Mount the ring base onto the scope mount, paying particular attention to the spacing
of the two rings relative to the scope body.
4. Once the proper ring placement on the mount has been determined, tighten the
base screws by hand. Carefully lay the scope into the open ring mounts and look
through the scope to ensure the reticle is in the desired position. * Note: You will
also need to ensure that the scope is mounted so that the proper eye relief is
achieved when aiming the firearm. Your scope is a “long eye relief scope,” with 8.5”
to 10.5” eye relief depending on the magnification power selected.
5. Replace the top halves of the rings. Reinsert the screws and tighten with the
provided hex wrench * Do not over-tighten. Over-tightening may damage the scope
tube.
6. Complete the final tightening of the ring bases with a standard screwdriver or coin.
ADJUSTING ELEVATION
1. Unscrew the cap located on elevation dial (located on top of scope) to expose the elevation
adjustment dial.
2. Turn the dial counter clockwise (noted on the dial as up with an arrow pointing to the left) in order
to raise the elevation/point of impact.
3. Turn the dial clockwise to the right to lower the elevation.
4. Replace the cap to protect the dials from being moved out of alignment
ADJUSTING WINDAGE
1. Unscrew the cap covering the windage knob.
2. Turn the knob clockwise to the right (noted on the knob face with an L and an arrow pointing to the
right) to move the windage/point of impact to the left.
3. Turn the knob counter clockwise to the left to move the windage/point of impact to the right.
4. Replace the cap to protect the knob from being moved out of alignment.
Focusing your scope
Your scope has a fine focus adjustment located on the ocular. To correct for vision or distance, grasp the
end of the eyepiece ring and turn the focus to the right or left until the desired focus is achieved.
Adjusting the laser
To adjust the windage and elevation on the laser attached to the scope, note the position of the windage
and elevation allen screws located on the laser. An allen wrench is provided to use to make the necessary
adjustments.
1. In order to move the laser up and down (elevation), insert the allen wrench into the top screw.
2. Turn the screw clockwise to move the laser down.
3. Turn the laser counter clockwise to raise the laser up.
4. To adjust the windage to the left, insert the allen wrench into the screw and turn it counter clockwise.
5. To move the laser to the right, turn the allen wrench clockwise.
RED LASERS SCOPE
(JHR2732B)
RINGS INCLUDED
ILLUMINATE RETICLE
1. Grasp the illumination dial located on left side of scope.
2. Turn the dial clockwise from the OFF position to the first number indicated on the dial.
3. View the target through the scope to determine if the reticle is bright enough to stand out clearly
against the target. To preserve the life of the battery, always remember to turn the illumination
dial to the OFF position when the scope is not in use. For prolonged
storage, remove the battery. If the reticle fails to illuminate or appears dim even on the highest
illumination setting, it is necessary to change the battery.
Changing the Illumination/Laser Battery
Your scopes use a 3-volt lithium CR2032 photo battery that powers both the laser and illumination.
1. Remove the battery cover by using a coin or screwdriver in the middle of the slot on the battery cap,
and remove.
2. Remove the old battery from its position in the center of the dial, and replace.
Maintenance & Care
Keep the scope in a place free from moisture, acid, or other corrosives.
Dust and dirt on the surface of the scope should be cleaned with a soft cloth
Dust on the lens should be cleaned with the cleaning cloth provided with your scope, or a cloth made
for cleaning optics
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
• Laser
• Illumination rheostat
• Mounting screws
• Scope rings
• Allen wrench